manualshive.com logo in svg

AMF Reece 101, Руководство по установке, Страница: 17 / 60

Поделиться
Скачать
AMF Reece 101 Скачать руководство пользователя страница 17

e-mail: [email protected]; [email protected] ; website: www.amfreece.com
Phones: +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606

Revised  09/2004

S-101

1-5

UPPER SYSTEM

Thread is
between
tension discs

Long groove

Detail

Use T-20 thrading wire for
threading needle bar

Detail

Spread washer so that
thread will rest in notch

THREADING OF FIXED TYPE TENSIONS

S p l i t   d i s c   t y p e

S o l i d   r o l l e r   t y p e

To needle bar

To needle bar

From thread
supply

From thread
supply

N o t e :

 Thread makes approximately one full turn

around the roller on this tension.

THREADING OF ROCKING TYPE TENSIONS

S p l i t   d i s c   t y p e

S o l i d   r o l l e r   t y p e

To needle bar

To needle bar

From thread
supply

From thread
supply

N o t e :

 Thread makes approximately 1 1/2 turns

around the roller on this tension.

N o t e :

 Refer to sheet 23 for additional information on threading Cord Trim Machines.

THREADING DIAGRAMS

Содержание Reece 101





























































Отзывы:

Нет отзывов