manualshive.com logo in svg

AMF Reece 101, Руководство по установке, Страница: 24 / 60

Поделиться
Скачать
AMF Reece 101 Скачать руководство пользователя страница 24

S-101

e-mail: [email protected]; [email protected]; website: www.amfreece.com

Phones: +420 582 309 146+ (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606

Revised  09/2004

1-12

NEEDLE BAR AND RACE LINE UP ADJUSTMENTS

Adjustment

 # 3

Vibration in line
with race
adjustments.

Adjustment 

# 2

For squareness of race
east and west across bed
plate.

Adjustment

 # 1

For 180

 o

 turn of race

It is imperative that the race swing east - west is only 180

o

 (# 3). It is

imperative that this 180 

o

 be square with the center line of the bed

plate (# 2). Also the needle bar assembly must vibrate squarely “east
and west” in harmony with the race (# 3).
To proceed with these adjustments, follow this sequence:
1. Adjust stud 

n

 to obtain adjustment # 1.

2. Loosen clamp screw 

q

 to obtain adjustment # 2.

3. Recheck adjustment # 1 - if wrong repeat adjustment # 2 and #
1 until they are reconciled.
4. When these adjustments are correctly, adjust the needle bar
assembly “east - west” in harmony with the race by loosening
screws 

p

 in sector B (# 3).

When assembling sector mesh
the teeth on sector with race
„north - south“ as in Fig. # 1
and # 4 so that sector teeth will
not disengage gear teeth at
either end of sewing

Adjustment 

# 4

MACHINE ADJUSTMENTS - CORRECTIVE AND MAINTENANCE

Содержание Reece 101





























































Отзывы:

Нет отзывов