manualshive.com logo in svg

AMF Reece 101, Руководство по установке, Страница: 11 / 60

Поделиться
Скачать
AMF Reece 101 Скачать руководство пользователя страница 11

e-mail: [email protected]; [email protected]; website: www.amfreece.com
Phones: +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606

Revised  09/2004

S-101

1-9

CONTENTS

              SHEET NO.

INSTRUCTION FOR INSTALLATION ON REECE INDIVIDUAL TABLES ............ 1-1

STOP MOTION ADJUSTMENTS ................................................................................... 1-2

MODEL 101 - SETTING UP INSTRUCTIONS .............................................................. 1-3

THREADING DIAGRAMS .............................................................................................. 1-4

MODEL 101 - OPERATING INSTRUCTIONS ............................................................... 1-7

ADJUSTMENTS THAT DETERMINE THE CHARACTER OF THE BUTTONHOLE

Needle information ............................................................................................... 1-8
Adjusting the bite and cutting space .................................................................... 1-9
To adjuste the clamp spread ................................................................................. 1-9
Adjusting the number of stitches per inch in a buttonhole ................................ 1-10
Increasing or decreasing of number of stitches in the eye independently
of the sides ............................................................................................................. 1-10
Tension ................................................................................................................... 1-10

MACHINE ADJUSTMENTS - CORRECTIVE AND MAINTENANCE

Needle bar and race line up adjustment ............................................................... 1-11
Equalizing the loopers .......................................................................................... 1-12
Looper and spreader adjustment .......................................................................... 1-13
To adjust play in split collar yoke ........................................................................ 1-14
To line up and adjust the cutting lever................................................................. 1-14
Adjusting the clamp operating mechanism ......................................................... 1-15
To adjust the trip lever .......................................................................................... 1-16
To correct distortion of eye................................................................................... 1-16
To adjust the roll pressure on length gauge ......................................................... 1-16
To adjust the rocker arm and stop motion ........................................................... 1-17
Adjusting the stop latch on stitching wheel ........................................................ 1-18
Adjusting the trigger setting mechanism ............................................................. 1-18
To adjust the timing of the L.H. handwheel in relation to rocker shaft and
lever ........................................................................................................................ 1-18
To adjust L.H. handwheel to disengage at the stopping position
of the machine ....................................................................................................... 1-19
To adjust for friction on worm shaft .................................................................... 1-19
To adjust for friction on main shaft ..................................................................... 1-19

Содержание Reece 101





























































Отзывы:

Нет отзывов