AmeriGlide STRATOS Скачать руководство пользователя страница 33

Страница: 33 / 40

STRATOS VERTICAL PLATFORM LIFTS:

Install Manual

04DEC2020 | 630-00147 REV A

TROUBLESHOOTING

STRATOS: SECTION 6

CONTACTOR TRAY

The Contactor Tray contains other control

electronics wired to motor and control tray.

See Figure 6-6.

Figure 6-6 (wires not shown)

UP AND DOWN

CONTACTORS

Both contactors have 3-poles with an auxiliary

circuit that are switched by 24V AC coils. On top of

the contactors is a switch position indicator that

can be observed to verify switching is occurring

properly. Contactors operate independently and are

controlled by the control board.

E-BRAKE RESISTOR

The E-Brake resistor electronically slows the

motor quickly via eddy current braking. When

both contactors are OFF the resistor essentially

shorts the motor leads which resists motor shaft

rotation. Braking is proportional to motor speed,

so this brake slows the motor very quickly, but

does not hold the motor from drifting after it stops.

The electromagnetic holding brake on the motor

is engaged after the motor comes to a stop. If the

platform is taking too long to come to a stop there

could be an issue with this resistor or the wiring on it.

LOAD RESISTORS

The load resistors function is to slow the platforms

speed in the DOWN direction. The resistors are

in-circuit only when the DOWN contactor is ON and

will generate significant heat as they dissipate some

of the downward energy. The fan located next to

the load resistors is there to cool the resistors.

COOLING FAN

The cooling fan is primarily to cool the load

resistors, but also cools the top compartment as it

pulls air from the tower below. The fan is controlled

by a thermostatic switch located on a load resistor.

If the fan is not cutting off when the temperature

drops there could be an issue with the switch.

BATTERY BACKUP

If the VPL is equipped with a Battery Backup System,

it will be located inside the tower below the top

plate. See Figure 6-7.

Do not manually switch the position indicator as
all safeties would be bypassed.

WARNING

Load resistors could be very hot. Do not touch.

WARNING

Motor

Brake

Fan

Load

Resistors

Contactor

DOWN

Contactor

E-Brake

Resistor

Motor

Gearbox

Содержание STRATOS









































Результаты поиска

Содержание STRATOS

Отзывы:

Похожие инструкции для STRATOS

Бренды по названию

Популярные бренды

AmeriGlide STRATOS, Руководство по установке

Результаты поиска

Содержание STRATOS

Отзывы:

Похожие инструкции для STRATOS

Бренды по названию

Популярные бренды