TWO BAY SYSTEMS, 64 CAMERAS x 8 MONITORS
Systems for a maximum of 64 cameras and 8 monitors are
supplied in two bays. The AD1653B bay contains a power
supply, processor, and monitor modules for monitors 1 through
8. The AD1654 bay contains the the camera modules for
cameras 1 through 64.
These systems are supplied in two bays configured as shown
below:
AD1653B AD1654
Modules/Panels
Bay
Bay
AD1603N PSM, Power Panel
1
-
Power Panel
-
1
AD1663B CPM, Data Panel
1
-
AD1611 VIM
-
1-8
AD1626 VOM
1-4
-
VIP Panel
-
1
For illustration of a typical two bay system with 64 cameras
and 8 monitors, see Page C-9 of the Typical System
Connections.
CAREFULLY IDENTIFY ALL BAYS, MODULES, AND
PANELS BEFORE PROCEEDING.
Power/Data Interconnections
A Power/Data Interconnection cable is supplied to provide
both operating power and control signals to the AD1654 bay
from the AD1653B bay. Connect the cable between connector
J1 on the AD1603N PSM Power Panel in the AD1653B bay
and connector J1 on the Power Panel in the AD1654 bay.
Control Code Connections
Control Code for all 64 cameras is provided from flying leads
on the supplied Power/Data Interconnection cable, above.
Video Interconnections
The camera video outputs from the AD1654 bay are provided
through eight BNC connectors, labeled 1, 3, 5, 7, and 2, 4, 6, 8,
on the VIP Panel.
Each AD1626 VOM in the AD1653B bay has two pairs of
input BNC connectors located on the upper portion of its back
panel for video interconnections from the VIP Panel. From the
rear, the input BNC for system monitor 1 is located at the
right-most VOM position, labeled MONITOR 1 A, and system
monitor 2 is the next position to the left, labeled MONITOR 2
A. System monitor 3 is on the next VOM panel to the left,
labeled MONITOR 3 A and system monitor 4 is labeled
MONITOR 4 A, and so on to system monitor 8 on the fourth
VOM panel. The “B” MONITOR BNC connectors are not
used in systems with 64 cameras or less.
AD1654 to AD1653B - Connect the top BNC on the AD1654
bay VIP Panel, labeled 1, to the top input BNC of the
AD1653B bay VOM panel for system monitor 1, labeled
MONITOR 1 A. Connect the BNC labeled 2 on the AD1654
bay VIP panel, to the top input BNC of the AD1653B bay
VOM panel for system monitor 2, labeled 2 A. Continue in
this manner until all eight connections of the AD1654 bay VIP
panel are connected to all eight “A” monitor input BNC’s of
the AD1653B bay VOM panels. If there are less than eight
monitors in the system, leave the remaining BNC’s on the VIP
panel unterminated.
DO NOT TERMINATE THE VIP PANELS.
Video Input Connections
Each AD1611 VIM in the AD1654 bay has eight terminated
BNC’s on the back panel for video input connections. The
system assigns the video input connected to the top BNC on
the right-most AD1611 VIM as input number 1. The video
input connected to the top BNC on the next AD1611 VIM to
the left is assigned as input number 9, etc., up to video input
number 64 on the bottom BNC of the last AD1611 VIM.
Video Output Connections
Each AD1626 VOM in the AD1653B bay has two BNC’s on
the bottom of its back panel (labeled OUT) for video output
connections. The system assigns the upper right OUT BNC on
the right-most AD1626 VOM as video output number 1, and
the lower left OUT BNC on this VOM as video output number
2. The upper-right OUT BNC on the next AD1626 VOM to
the left is assigned as video output number 3, etc., up to video
output number 8 on the fourth VOM.
SYSTEM CONFIGURATIONS
AD1650B
3-4
