THREE BAY SYSTEMS, 128 CAMERAS x 8 MONITORS
Systems for a maximum of 128 cameras and 8 monitors are
supplied in three bays. The AD1653B bay contains a power
supply, a processor, and monitor modules for monitors 1
through 8. The AD1654 bay contains the camera modules for
cameras 1 through 64. The AD1655 bay contains a power
supply and camera modules for cameras 65 through 128.
These systems are supplied in three bays configured as shown
below:
AD1653B AD1654 AD1655
Modules/Panels
Bay
Bay
Bay
AD1603N PSM, Power Panel
1
-
1
Power Panel
-
1
-
AD1663B CPM, Data Panel
1
-
-
AD1611 VIM
-
8
1-8
AD1626 VOM
1-4
-
-
VIP Panel
-
1
1
For illustration of a typical Three Bay system with 128
cameras and 8 monitors, see Page C-10 of the Typical System
Connections.
CAREFULLY IDENTIFY ALL BAYS, MODULES, AND
PANELS BEFORE PROCEEDING.
Power/Data Interconnections
A Power/Data Interconnection cable is supplied to provide
both operating power and control signals to the AD1654 bay
from the AD1653B bay. Connect the cable between connector
J1 on the AD1603N PSM Power Panel in the AD1653B bay
and connector J1 on the Power Panel in the AD1654 bay.
A separate Data Interconnect cable is supplied to provide
control data to the AD1655 bay. Connect this Data cable
between connector J2 on the Data Panel in the AD1653B bay
and connector J2 on the Power Panel in the AD1655 bay.
Control Code Connections
Control Code for cameras 1-64 is provided from flying leads
on the Power/Data cable from connector J1 on the AD1653B
bay. Control Code for cameras 65-128 is provided from
connector J1 on the Power Panel in the AD1655 bay.
Video Interconnections
The camera video outputs from the VIP Panels on the AD1654
(cameras 1 to 64) and AD1655 (cameras 65 to 128) bays are
provided through eight BNC’s, labeled 1, 3, 5, 7, and 2, 4, 6, 8.
Each AD1626 VOM in the AD1653B bay has two pairs of
input BNC’s located on the upper portion of its back panel for
video interconnections from the VIP panels. Outputs from the
AD1654 bay connect to the AD1653B bay “A” MONITOR
BNC’s. Outputs from the AD1655 bay connect to the
AD1653B bay “B” BNC’s.
From the rear of the AD1653B bay, the input BNC for system
monitor 1 is located at the right-most VOM position in the bay,
labeled MONITOR 1 A and 1 B, and system monitor 2 is
labeled MONITOR 2 A and 2 B. System monitor 3 is on the
next VOM panel to the left, labeled MONITOR 3 A and 3 B,
and system monitor 4 is labeled MONITOR 4 A and 4 B, and
so on to system monitor 8 on the fourth VOM panel.
AD1654 to AD1653B - Connect the top BNC on the AD1654
bay VIP Panel, labeled 1, to the top input BNC of the
AD1653B bay VOM panel for system monitor 1, labeled
MONITOR 1 A. Connect the BNC labeled 2 on the AD1654
bay VIP panel, to the top input BNC of the AD1653B bay
VOM panel for system monitor 2, labeled 2 A. Continue in
this manner until all eight connections of the AD1654 bay VIP
panel are connected to all eight “A” monitor inputs of the
AD1653B bay VOM panels. If there are less than eight
monitors in the system, leave the remaining BNC’s on the VIP
panel unterminated.
DO NOT TERMINATE THE VIP PANELS.
AD1655 to AD1653B - Connect the top BNC on the AD1655
bay VIP Panel, labeled 1, to the second input BNC of the
AD1653B bay VOM panel for system monitor 1, labeled
MONITOR 1 B. Connect the BNC labeled 2 on the AD1655
bay VIP panel, to the second input BNC of the AD1653B bay
VOM panel for system monitor 2, labeled 2 B. Continue in
this manner until all eight connections of the AD1655 bay VIP
panel are connected to all eight “B” monitor inputs of the
AD1653B bay VOM panels. If there are less than eight
monitors in the system, leave the remaining BNC’s on the VIP
panel unterminated.
DO NOT TERMINATE VIP PANELS.
(Continue on the next page for Video Input and Output
Connections for this configuration.)
AD1650B
SYSTEM CONFIGURATIONS
3-5
