background image

User Instructions

ADJ Products, LLC - www.adj.com - Royal 3D II Instruction Manual Page 2

Unpacking: 

Thank you for purchasing the Royal 3D II by ADJ Prod-

ucts, LLC. Every Royal 3D II has been thoroughly tested and has been 

shipped in perfect operating condition. Carefully check the shipping 

carton for damage that may have occurred during shipping. If the 

carton appears to be damaged, carefully inspect your fixture for any 

damage and be sure all equipment necessary to operate the unit has 

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further 

instructions. Please do not return this unit to your dealer without con-

tacting customer support first. 

Introduction: 

The Royal 3D II is an incredible five channel DMX intel-

ligent, green and violet blue laser fixture. The blue laser combined with 

the green laser create amazing aerial effects on a ceiling or wall. The 

Royal 3D II can operate as a stand alone fixture, or in a Master/Slave 

configuration. The Royal 3D II has two operating modes; sound active 

or controlled via DMX.  This  fixture  is  suitable  for  theaters,  studios, 

retail stores, and other similar locations. For best results use fog or 

special effects smoke to enhance the beams projections.  

Customer Support:

 

ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and  to answer any question 

should you encounter problems during your set up or initial operation. 

You may also visit us on the web at www.adj.com for any comments 

or suggestions. For service related issue please contact ADJ Products, 

LLC. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. 

Pacific Standard Time.

 

Voice:   

(800) 322-6337

 

Fax:    

(323) 582-2941

 

E-mail:  

[email protected]

Warning!

 

To prevent or reduce the risk of electrical shock or fire, do 

not expose this unit to rain or moisture. 

Caution! 

There are no user serviceable parts inside this unit. Do not 

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact 

ADJ customer support.
PLEASE recycle the shipping carton whenever possible.

 Royal 3D II   

 

                    General Introduction

   3/13

ROYAL 3D II

Содержание ROYAL 3D II











Отзывы: