ADJ Products, LLC - www.adj.com - Royal 3D II Instruction Manual Page 4
ADJ Products, LLC - www.adj.com - Royal 3D II Instruction Manual Page 3
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future
reference.
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Royal 3D II
General Instructions
Safety Issues: This unit may “pop” the fuse if the maximum allotted
load of 7 amps is reached.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short. Do not attempt to oper-
ate this unit if the power cord has been frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked
on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 18 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
• 30mW Green Laser & 350mW Violet Blue Laser
• 5 Channel DMX Control
• 2 Operating Modes - Sound Active & DMX Control
• Digital Display for Address and Function Setting
• UC3 Controller (Not Included)
• Run as Stand Alone unit or in a Master-Slave Configuration
• Power Cord Daisy Chain up to 14 units max. See page 16
Royal 3D II
Features
Royal 3D II
Warranty Registration
The Royal 3D II carries a 90 day limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned ser-
vice items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. If the unit is
under warranty you must provide a copy of your proof of purchase
invoice. Please contact ADJ customer support for a R.A. number.
The unit should be mounted using a mounting clamp (not provided),
affixing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is firmly fixed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the fixture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
Royal 3D II
Installation
Royal 3D II
Safety Precautions
!
!
LASER RADIATION
AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 532nm, 450nm
Class IIIa laser product
This device complies with 21 CFR
chapter I,
Subchapter J, CFR 1040.10 and 1040.1
1
