background image

ADJ Products, LLC  -  www.adj.com  - Inno Spot LED WiFly Instruction Manual Page 6

ADJ Products, LLC  -  www.adj.com  - Inno Spot LED WiFly Instruction Manual Page 7

Power Supply:

 Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your ADJ Inno Spot 

LED WiFly. The ADJ Inno Spot LED WiFly is available in a switchable 

120v and 220v version. Because line voltage may vary from venue to 

venue, you should be sure your unit voltage matches the wall outlet 

voltage before attempting to operate you fixture.  Also be sure to only 

use the included I.E.C. power cable supplied with the unit, this cable 

matches the voltage and current requirements of the unit.

DMX-512:

 DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of 

communication between intelligent fixtures and controllers. A  DMX 

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture 

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX 

fixtures (most controllers only have a DATA “OUT” terminal). 

DMX Linking: 

DMX  is  a  language  allowing  all  makes  and  models 

of different manufactures to be linked together and operate from a 

single  controller,  as  long  as  all  fixtures  and  the  controller are DMX 

compliant.  To ensure proper DMX data transmission, when using 

several DMX fixtures try to use the shortest cable path possible. The 

order in which fixtures are connected in a DMX line does not influence 

the DMX addressing. For example; a fixture assigned a DMX address 

of 1 may be placed anywhere in a DMX line, at the beginning, at the 

end, or anywhere in the middle. Therefore, the first fixture controlled 

by the controller could be the last fixture in the chain. When a fixture 

is assigned a DMX address of 1, the DMX controller knows to send 

DATA assigned to address 1 to that unit, no matter where it is located 

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX 

and Master/Slave Operation): 

The Inno Spot LED 

WiFly  can  be  controlled  via  DMX-512  protocol. 

The  Inno  Spot  LED  WiFly  is  a  ten  channel  DMX 

unit. The DMX address is set electronically using 

the  controls  on  the  front  panel  of  the  unit.  Your 

unit and your DMX controller require a approved 

DMX-512 110 Ohm Data cable for data input and 

 Inno Spot LED WiFly                                                 Set Up

Figure 1

Screw one clamp via a M12 screw and nut onto the Omega 

holder. Insert the allen bolts into the respective holes on the 

bottom of the Inno Spot LED WiFly. Attach the safety-cable 

through the eyehole hook on the bottom of the base and over 

the trussing system or a safe fixation spot. Insert the end in the 

carabine and tighten the safety screw.

NOTICE:

 The suitable enviromental temperature for this light-

ing fixture is between -25˚ C to 45˚ C. Do not place this lighting 

fixture in an enviroment where the temperatures are under or 

above the temperatures stated above. This will allow the fixture 

to run at its best and help prolong the fixture life. 

 Inno Spot LED WiFly    

                         Installation

Содержание INNO SPOT LED WIFLY















Отзывы: