InstructIon MAnuAL for:
CORDLESS INSPECTION LAMP
MoDEL no :
LED28
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE
FOR FUTURE USE.
1. SAFETY
2. INTRODUCTION
3. CHARGING
IMPORTANT WARRANTY INFORMATION:
the battery fitted to this cordless tool is considered to
be a consumable item and its ability to accept charge
will reduce over time. We will warranty it against
mechanical and electrical defect for a period of one
year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or
regularly conditioned, its capacity will diminish.
under these circumstances we will not replace the
battery even if it is less than one year old.
3.1
Make sure the inspection lamp is switched off before
commencing charging.
3.2
uncoil the charging lead and plug the connector into
the charging socket built into the end of the inspection
lamp handle.
• Robust housing with bumper ring.
• 28 LEDs super bright LEDs.
• Incorporates LED charging indicator.
•
Integral hanging loop and spring loaded gripper.
•
Ideal for use in engine bays and dull work areas.
•
Battery service life: 3.5 to 7 hours per charge.
• Supplied with mains charger.
• Charging time: 14 hours.
• Charging output: 6V 500 mA DC.
• On/Off switch offers high or low output.
1.1. GENERAL
DO NOT
shine directly into your, other person’s or animal’s eyes.
DO NOT
allow children to use the inspection lamp.
DO NOT
handle or move the inspection lamp whilst it is being charged.
DO NOT
use the inspection lamp if you suspect that the battery or the inspection lamp casing is damaged.
DO NOT
leave battery in a discharged state: recharge battery immediately.If the inspection lamp is not in use,
recharge the battery every 3 to 4 weeks.
1.3. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING INSPECTION LAMP TO THE POWER SUPPLY.
WARNING!
It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An rccB
(residual current circuit Breaker) should be incorporated in the main distribution board. We also recommend that an
rcD (residual current Device) is used with all electrical products, particularly portable equipment which is plugged into
an electrical supply not protected by an rccB.
You must
also read and understand the instructions concerning electrical safety paragraph 1.3.1 onwards.
1.3.1.
The Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.3.2. The Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition
of the appliance and the safety of the appliance operator.
If in any doubt, contact a qualified electrician.
1.3.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the
mains power supply. If worn or damaged
DO NOT
use.
Important: check that the voltage marked on the charger plug is the same as the power supply to be used.
uncoil the cable between charger and the inspection lamp.
DO NOT
pull the charger plug from the mains socket by the lead.
DO NOT
use any other type of charger with this inspection lamp.
DO NOT
try to take the charger plug apart.
DO NOT
use the charger plug to charge or power any other electrical item.
DO NOT
get the charger wet, or use in wet, damp conditions (for indoor use only).
WARNING!
NEVER
substitute a standard 13amp 3 pin plug, or any other type of plug, for the charger plug.
Original Language Version
LED28 Issue: 3 - 09/01/12
