background image

ENGLISH

ins 5 0003  rev 1027

CAUTION!

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer

or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.

LAMP ASSEMBLY
1.

Unpack all lamp parts and lay out

on the floor with the base (A) lying
flat.

2.

Thread pole (B) to adjustable arm

by hand, turning clockwise until
tight.

3.

Thread pole (B) to base (A) by

hand, turning clockwise until tight.

4.

Pull excess wire through bottom

of base.

5.

Attach harp (C) to socket 

brackets (H) by squeezing open
ends of harp, placing flattened 
section inside of brackets (H) and
releasing. End by sliding caps (G)
over brackets (H).

6.

Place shade (D) on harp (C).

7.

Place reflector (E) on top of shade

(D), making sure the white side faces
down.

8.

Attach finial (F) to top of harp

(C), turning clockwise until tight.

9.

Install bulb following BULB

INSERTION/ REPLACEMENT
instructions.

10.

Plug the lamp into a standard

120V outlet.

11.

Turn lamp on or off by rotating

the switch (J) located on the socket
clockwise.

BULB INSERTION/REPLACEMENT
1.

Make sure the lamp is not

plugged into an electrical socket.

2.

If the lamp has been in use, allow

it to cool for approximately five 
minutes before proceeding.

3.

To install a bulb in the socket,

hold the bulb firmly near the base,
align bulb pins with matching pin-
holes then push it straight into the
socket until it "snaps" into place.

4.

To remove a bulb already installed

in the lamp, grasp it firmly at the
base and, using a slight rocking
motion, pull it straight out of the
socket. 

Do not twist or turn the

bulb.

Please note that in operation,
OTT-LITE

®

bulbs are not dimmable.

Enjoy your OTT-LITE

®

Collins Table

Lamp!

This lighting system is designed for
use with OTT-LITE VisionSaver Plus

®

bulbs only (model number
B84J35). Use of other products
voids the warranty and may result
in damage to the lighting system.

CAUTION! IMPORTANT SAFETY INSTRUCTIONS:

THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED
ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED. DO NOT ALTER 
THE PLUG.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

CAUTION:

BALLAST REQUIRES PROPER VENTILATION FOR PROPER OPERATION. A MINIMUM OF 6 

INCHES OF AIR SPACE MUST BE PROVIDED ON ALL SIDES EXCEPT WHERE PLUGGED INTO AN ELECTRICAL OUTLET.

AVERTISSEMENT! IMPORTANTES DIRECTIVES DE

SÉCURITÉ:

CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE

L'AUTRE). CE DISPOSITIF DE SÉCURITÉ DIMINUE LE  RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE
S'INSÈRE DANS LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF
SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.

AVERTISSEMENT:

POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE

DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.

ATTENTION:

LES BALLASTS NÉCESSITENT UNE VENTILATION ADÉQUATE POUR UN FONCTIONNEMENT

CORRECT. UN MINIMUM DE 15 CM D'ESPACE DOIT ÊTRE LAISSÉ DE CHAQUE COTÉ À L'EXCEPTION DE CELUI OÙ
SE TROUVE LE BRANCHEMENT À LA PRISE D'ALIMENTATION ÉLECTRIQUE.

¡PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD

IMPORTANTES:

ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES

MÁS ANCHA QUE LA OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA.
ESTE ENCHUFE ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE
NO CALZA COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA.  SI AÚN NO ENCAJA, PÓNGASE EN 
CONTACTO CON UN ELECTRICISTA CALIFICADO.  NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE
PUEDA SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.

PRECAUCIÓN:

PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL

ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.

PRECAUCIÓN:

LA RESISTENCIA NECESITA UNA ADECUADA VENTILACIÓN PARA FUNCIONAR 

CORRECTAMENTE. DEBE PROVEERSE UN ESPACIO DE AIRE DE UN MÍNIMO DE 6" EN TODOS LOS LADOS, 
EXCEPTO DONDE ESTÁ CONECTADA A UN TOMACORRIENTE. 

20W Collins Table Lamp

20W 

Collins Table Lamp

20C83462

Reviews: