manualshive.com logo in svg

AMCI SV160E2, Руководство пользователя, Страница: 28 / 120

Поделиться
Скачать
AMCI SV160E2 Скачать руководство пользователя страница 28

M

OTION

 C

ONTROL

SV160E2 User Manual

ADVANCED MICRO CONTROLS INC.

28

Controlled and Immediate Stops

Once a move is started, there are several ways to stop the move before it comes to an end. These stops are 
broken down into two types:

Controlled Stop:

  The axis immediately begins decelerating at the move’s programmed deceleration 

value until it reaches zero speed. The motor position value is still considered valid after a Controlled 
Stop and the machine does not need to be homed again before Absolute Moves can be run.

Immediate Stop:

  The 

Immediate Stop Deceleration

 parameter, described on page 26, is used to decel-

erate the load. If the Immediate Stop Deceleration parameter is set to zero, the move stops immediately, 
without deceleration. If the position error during the stop does not exceed the Maximum Position Error 
Limit value, the motor will stop at the Profile Position value.  If the position error during the stop 
exceeds the Maximum Position Error Limit value, the SV160E2 will disable the motor and issue a 
Position_Invalid fault. 

Host Control

Hold Move Command:

  This command can be used with some moves to bring the axis to a Controlled Stop. 

The move can be resumed and finished, or it can be aborted. Not all moves are affected by this command. The 
section 

Basic Move Types

, starting on page 29, describes each move type in detail, including if the move is 

affected by this command.

Immediate Stop Command: 

 The 

Immediate Stop Deceleration

 parameter, described on page 26, is used to 

decelerate the load. If the Immediate Stop Deceleration parameter is set to zero, the move stops immediately, 
without deceleration. If a stall is not detected during the stop, the motor will return to the Profile Position 
value. If a stall is detected during the stop the SV160E2 will disable the motor and issue a Position_Invalid 
fault.  See 

Stall Detection

 on page 16 for a description of the stall detection process.

Hardware Control

Stop Jog or Registration Move Input: 

Triggering this input type during a Jog Move or Registration Move 

will bring the move to a controlled stop. The controlled stop is triggered on an inactive-to-active state change on 
the input. Only Jog Moves and Registration Moves can be stopped this way, all other moves ignore this input.

CW Limit and CCW Limit Inputs:

  In most cases, activating these inputs during a move will bring the axis to 

an Immediate Stop. The 

Immediate Stop Deceleration

 parameter, described on page 26, is used to decelerate 

the load. The exceptions are the 

CW/CCW Find Home

 commands, the 

CW/CCW Jog Move

 commands, and 

the 

CW/CCW Registration Move

 commands. The 

Find Home

 commands are explained in the reference sec-

tion, 

Homing an SV160E2

, which starts on page 41. The 

CW/CCW Jog Move

 commands are fully explained 

on page 31, and the 

CW/CCW Registration Move

 commands are fully explained on page 32.

Emergency Stop Input:

  It is possible to configure an input as an Emergency Stop Input. When an Emer-

gency Stop Input is activated, the axis will come to an Immediate Stop. The move cannot be restarted. The 

Immediate Stop Deceleration

 parameter, described on page 26, is used to decelerate the load. If a stall is not 

detected during the stop, the motor will return to the Profile Position value. If a stall is detected during the 
stop, the SV160E2 will disable the motor and issue a Position_Invalid fault.  See 

Stall Detection

 on page 16 

for a description of the stall detection process.

Содержание SV160E2

























































































































Отзывы:

Нет отзывов