manualshive.com logo in svg

AMCI ANR2, Руководство пользователя

Поделиться
Скачать
AMCI ANR2 Скачать руководство пользователя страница 55

20 Gear Drive, Plymouth Ind. Park, Terryville, CT 06786

Tel: (860) 585-1254  Fax: (860) 584-1973  http://www.amci.com

A

LIGNMENT

 M

ODE

 D

ATA

 F

ORMAT

7

55

Setting the Maximum Value

The next step in aligning the ANR2 is to set the Maximum Value.  Before you can write the command down 
to the ANR2, you must physically drive the sensor to the position where you define the point.  

1) When using One-Sided or Two-sided Symmetrical Alignments, you define the null value 

and the value at one of your position extremes.  You can use either the Set Minimum Value 
or Set Maximum Value commands to set your outer position.  You will not use both. 

2) The programmed Maximum Value can be less than the programmed Null Value.  The only 

restrictions on programming the Maximum Value is that it must be in the range of Null 
Value ± 65,535 counts with a maximum of ±2,147,483,647, and, for two sided alignment, 
on the other side of the null point from the programmed Minimum Value.

3) When using the Two Point Linear Alignment method, you must know the value of the A-D 

converter readings before issuing the Set Minimum Value or Set Maximum Value com-
mands.  Issue the Set Maximum Value command first only if the magnitude of your high 
reading is greater than the magnitude of your low reading.  This occurs when your positive 
reading has a greater magnitude than your negative reading.

4) When not using the Two Point Linear Alignment method, the points where you set the Min-

imum and Maximum Values must be on the opposite sides of the null point. 

Channel Position Value

While setting the Maximum Value, the channel’s position registers holds the raw A-D converter value in 32 
bit sign-magnitude format.  The A-D converter value for channel 1 is in words 2 and 3 of the Network Input 
Data.  The A-D converter value for channel 2 is in words 6 and 7.  A description of the 

Network Input Data

 

format is started on page 37.  

1) The ANR2 will not allow you to set the Maximum Value until the A-D converter value is at 

least 100 counts different from all other programmed positions.

2) The maximum ADC value is ±8,191 counts.  If the A-D converter reaches this value before 

you reach the outer limit of your travel, then your Sensor Sensitivity parameter is set too 
high or your Sensor Displacement parameter is set too low.  If you are not using the Two 
Point Linear Alignment method, you will have to enter Configuration Mode to adjust one or 
both of these parameters.  See chapter 6. 

Configuration Mode Data Format

, starting on 

page 43 for more information on Configuration Mode programming.

Содержание ANR2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды