manualshive.com logo in svg

AMCI ANR2, Руководство пользователя

Поделиться
Скачать
AMCI ANR2 Скачать руководство пользователя страница 16

O

PERATING

 M

ODES

ADVANCED MICRO CONTROLS INC.

2

16

Available Modes  (continued)

Alignment Mode

After the module is configured, Alignment Mode is used to set the Minimum, Maximum, and Null Values.  
Note that each channel is programmed separately

† The Null Value is not set when using the Two Point Linear method.  When using this method, the maxi-

mum distance between the Minimum Value and Maximum Value is 65,535 counts.  Both values must be in 
the range of ±2,147,483,647.

Table 2.2  Alignment Parameters

Measurement Mode

After the sensor is aligned, use Measurement Mode to read back the position and velocity values from your 
sensor.  If the ANR2 automatically enters Measurement Mode after you exit a different mode, you must issue 
a command to the unit to tell it which channels to read.

Status Bits

The ANR2 has five module status bits so you can determine the state of the module.  It also has four status 
bits per channel to tell you what valid data exists for the channel and if the ANR2 is actively measuring the 
position of the sensor.

Module Status Bits

Module Initialized: 

 This bit is set on power up or after a hardware reset.  The ANR2 is only transmitting status 

information.  Position data is set to zero.  The module is waiting for the first command from the host 
controller.

In Calibration Mode:

  If this bit is set along with the 

Module Initialized

 bit on power up, the ANR2 requires cal-

ibration.  If it is set when the 

Module Initialized

 bit is reset, the unit is in Calibration Mode.

In Configuration Mode:

  If this bit is set along with the 

Module Initialized

 bit on power up, the ANR2 does not 

have valid configuration data for either channel.  If it is set when the 

Module Initialized

 bit is reset, the 

unit is in Configuration Mode.  Use the Channel Status bits to determine which channels require con-
figuration.

In Alignment Mode:

  If this bit is set along with the 

Module Initialized

 bit on power up, the ANR2 does not 

have valid alignment data for either channel.  If it is set when the 

Module Initialized

 bit is reset, the 

unit is in Alignment Mode.  Use the Channel Status bits to determine which channels require align-
ment.

In Measurement Mode:

  If this bit is set along with the 

Module Initialized

 bit on power up, the ANR2 is ready 

to measure position on at least one of the channels.  If it is set when the 

Module Initialized

 bit is reset, 

the unit is in Measurement Mode.  Use the Channel Status bits to determine which channels the 
ANR2 is actively measuring.

Channel Status Bits

Channel Calibrated:

  Valid calibration data exists for the channel.

Channel Configured:

  Valid configuration data exists for the channel.

Channel Aligned:

  Valid alignment data exists for the channel.

Channel Measuring:

  The ANR2 is actively measuring the position of the sensor.

Parameter

Range

Units

Null Value

†

±2,147,483,647

Counts

Minimum Value

Null Position ± 65,535 

±2,147,483,647 max.

Counts

Maximum Value

Null Position ± 65,535 

±2,147,483,647 max.

Counts

Содержание ANR2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды