Amano 07001A, Руководство оператора

Страница: 4 / 33

6 7
EN EN
Introduction
Electrical Connection Instructions
CAUTION:
Your equipment may be inappropriate on some installations. Some softer woods used in flooring cannot support the
pressure created by hard wheels. Always consult with the flooring manufacturer on the proper installation, preparation,
and finishing of their product. Determine suitability of your equipment in preparing the product.
Tool Storage Tray
Leveling Adjustment
Sanding Pres. Adjust
Motor Starter / Protector
Operating Controls
CAUTION:
This machine will operate only on AC fre-
quency and on electrical voltage shown on
the equipment nameplate. Make sure you
have the correct frequency and voltage before
connecting the power cord to an outlet. See
the example in figure 1.
This machine must be connected to an electrical source with an
earthing conductor in order to protect the operator from electric
shock. This machine has an approved power cord with three
conductors as well as a plug with three terminals. Connect the
plug to a matching receptacle.
DANGER:
Electrocution could occur if the machine is
exposed to water or rain. Keep the machine
in a dry building.
DANGER:
Electrocution could occur if machine is not
connected to an electrical source with an
earthing conductor. To prevent possible
electric shock, use an electrical cord with an
earthing conductor and connect it to a match-
ing electrical source. For maximum protection
against electrical shock, use a circuit that is
protected by a ground fault circuit interrupter.
Consult your electrical contractor.
DANGER:
Electrocution could occur if the machine is
used with a damaged plug or power cord. If
the cords or plugs are worn or damaged in
any way, have them replaced by an authorized
service person or electrician.
Extension Cords
Use only an approved three-pronged extension cord with two main
conductors and one earthing conductor. This machine is equipped
with a power cord. When greater range is needed follow the table
below to determine cable gauge of additional footage. Refer to
the chart to the right for extension cord information.
If motor appears to labor or takes a considerable longer time to
come up to speed reduce sanding pressure.
Source Voltage 0 - 100' 100 - 250'
Feet/Wire Guage (Stranded Copper)
208 6
230 10 8
Use Voltage
Booster
Figure 1
07108A / 07204A / 07108C 07109A
07120A
MODEL
07001A / 07108B
Electrical Requirements ~208-240V 60 Hz ~220-240V 50 Hz ~220-240V 50 Hz -230V6 0 Hz 3Ø
Amperage 15.7 11.8 11.8 24
Sound Emisson{Lpm) 83.0 dB(A) 79.4 dB(A) 79.4d B(A) 83.0 dB(A)
Contact Wheel Rate(rpm) 2000/240 1670/200 1670/2000 2000/240
Abrasive Rate 3800/4560 ft/ min 970/1160 m/min 970/1160 m/min 3800/4560 ft/ min
Abrasive Sheet Size 280 CFM 970/1160 m/min 970/1160 m/min 3800/4560 ft/ min
Fan Flow Rate 12" x261/8" 305mm x 664mm 305mm x 664mm 12" X 26 1/8"
Motor 4 Hp Continuous 2.2 kW Continuous 2.2 kW Continuous 10 Hp
Overload Protection Magnetic Circuit Breaker Magnetic Circuit Breaker 13 A Fuse Magnetic Circuit Breaker
Operating Controls Adjustable Lever/Grip Adjustable Lever/Grip Adjustable Lever/Grip Adjustable Lever/Grip
Leveling Controls Externally Adjustable Externally Adjustable Externally Adjustable Externally Adjustable
Electrical Cable 100' 10-3 SJO with H05VVF3G4.0 H07RNF3G1.5 mm N/A
L6-20P Plug AU3-20P Plug with UK1-13P Plug
Operating Wheels 80 Durometer 80 Durometer 80 Durometer 80 Durometer
Clear Urethane Clear Urethane Clear Urethane Clear Urethane
Weight 240 lbs. 204 lbs. 92.7 kg 256 lbs
Dimensions 40½X 15X 36 3/4 40½X 15X 36 3/4 103cmx 38cmx 93cm 40½X 15X 36 3/4