3
EN
2
EN
***This product is intended for commercial use only***
WARNING!
The Products sold with this Manual contain or may contain chemicals that are known to certain governments (such as the State of
California, as identified in its Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other reproductive harm. In
certain locations (including the State of California) purchasers of these Products that place them in service at an employment job site
or a publicly accessible space are required by regulation to make certain notices, warnings or disclosures regarding the chemicals that
are or may be contained in the Products at or about such work sites. It is the purchaser’s responsibility to know the content of, and
to comply with, any laws and regulations relating to the use of these Products in such environments. The Manufacturer disclaims any
responsibility to advise purchasers of any specific requirements that may be applicable to the use of the Products in such environments.
In this Operation Manual you will find three statements that you must read and observe to ensure safe operation of this
machine.
DANGER
means: Severe bodily injury or death can occur to you or other personnel if the
DANGER
statements
found on this machine or in this Operation Manual are ignored or are not adhered to. Read and observe
all
DANGER
statements found in this Operation Manual and on your machine.
WARNING
means: Injury can occur to you or to other personnel if the
WARNING
statements found on your
machine or in the Operation Manual are ignored or are not adhered to. Read and observe all
WARNING
statements found in this Operation Manual and on your machine.
CAUTION
means:
Damage can occur to the machine or to other property if the
CAUTION
statements found
on your machine or in this Operation Manual are ignored or are not adhered to. Read and observe all
CAUTION
statements found in this Operation Manual and on your machine.
Operator Safety Instructions
DANGER:
Failure to read the Owner’s Manual prior to operating or servicing your American Sanders machine could result in injury to
you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the
operation of this machine before using it. If you or your operator(s) cannot read English, have this manual explained fully
before attempting to operate this machine.
DANGER:
A. Sanding/finishing wood floors can create an explosive or combustible environment. Do not operate this machine around
solvents, thinners, alcohol, fuels, floor finishes, wood dust or any other flammable materials. Cigarette lighters, pilot lights,
electrical sparks and all other sources of ignition should be extinguished or avoided. Keep work area well ventilated.
B. Dust generated from sanding wood floors can spontaneously ignite or explode. Promptly dispose of any sanding dust in
a metal container clear of any combustibles. Do not dispose in a fire.
DANGER:
A. Electrocution could occur if the machine is being serviced while the machine is connected to a power source. Disconnect
the power supply before servicing.
B. Electrocution or fire could occur if the machine is being operated with a damaged power cord. Keep the power cord clear
of the pad. Always lift the cord over the machine. Do not move the machine by the power cord.
C.Shock hazard. Do not use the machine if it has been rained on or sprayed with water.
DANGER:
To avoid injury keep hands, feet, and loose clothing away from all moving parts on the machine. Disconnect the power cord
before replacing the pad, changing the abrasive, or when servicing. Do not operate the machine unless all guards are in
place. Never leave the machine unattended while connected to a power source.
WARNING:
Injury can occur if protective clothing or equipment is not used while sanding. Always wear safety goggles, protective
clothing, and dust mask while sanding.
WARNING:
This sander is not to be used on pressure treated wood. Some pressure treated woods contain arsenic and sanding
pressure treated wood produces hazardous dust. Inhaling hazardous dust from pressure treated wood can cause serious
injury or death. Sanding pressure treated wood decks or uneven surfaces can damage the sander which is not covered
under warranty or damage waiver.
WARNING:
Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other
bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities.
WARNING:
Risk of explosion. Floor sanding can result in an explosive mixture of fine dust and air. Use floor sanding machine only in a
well-ventilated area free from any flame or match.
SECTION II - Parts and Service Manual
Handle Assy (Models 07108A, 07109A, 07204A, 07108C) .................. 36
Handle Assy (Model 07001A, 07108B)................................................. 38
Handle Assy (Model 07120A). .............................................................. 40
Motor Assy (Model 07001A, 07108B). .................................................. 42
Motor Assy (Models 07108A, 07109A, 07204A, 07108C) .................... 43
Motor Assy (Model 07120A) ................................................................. 44
Drum Assy ............................................................................................ 45
Dust Control Assy ................................................................................. 46
Base Assy ............................................................................................. 48
Base Assy (Models 07044C, 07049C).................................................. 50
Belt Guard Assy (Models 07108A, 07109A, 07204A, 07108C) ............ 52
Belt Guard (Model 07001A, 07108B) ................................................... 53
Belt Guard (Model 07120A) .................................................................. 54
Accessories .......................................................................................... 55
Wiring Diagrams ................................................................................... 56
Warranty ............................................................................................... 58
Contents
Operator Safety Instructions ...............................2
Introduction and Machine Specifications ............6
230V Electrical Connection Instructions ............. 7
How to Transport the Machine............................8
Machine Set-Up ..................................................9
How to Operate the Machine ............................10
Sanding Cuts and Sandpaper ..........................13
Sander Adjustment Procedures ........................13
Routine Maintenance........................................15
Troubleshooting ................................................16
Chatter-Wave Prevention .................................17
General Power Tool Safety Warnings
WARNING: Read all safety warnings and instructions.
Failure to follow warnings and instructions may result in electric
shock, fire and or serious injury
.
Save all warnings and instructions for future use.
The term "power tool" in the warnings refers to your main-operated (corded) power tool or battery operated (cordless) power tool.
1) Work area safety
a)
Keep work area clean and well lit.
Clutter or dark areas invite accidents .
b)
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gasses, or dust.
Power tools create sparks which may ignite the dust or fumes.
c)
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a)
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock .
b)
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators.
There is an
increased risk of electric shock if your body is earthed or grounded .
c)
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e)
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of cord suitable for outdoor
use reduces the risk of electric shock .
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating
or attempting any service or maintenance procedure to your American Sanders machine could result in injury to you or to other
personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine
before using it. If your operator(s) cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.