Amada MG3 Hot Bar Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 49

Amada MG3 Hot Bar Скачать руководство пользователя страница 23

MG3 Hot Bar

How to …?

76609576EN-MG3-HB-V1_0a.docx 23/49

DATE
Set the current date in the format YY-MM-DD (year-month-day)

TIME

Set the current time in the format HH:MM:SS (hour:minute:second)

GRAPHIC VIEW
Enables graphic viewing (ON/OFF). If you disable this check box, no graphics

will be shown.

COMMUNICATION SETTINGS

Adjust the settings for communication via Ethernet, CANopen or Bus
modules.

Click SYSTEM to change to

SYSTEM

screen.

The

SYSTEM

screen displays general system information. E.g. about:



MAINBOARD

(RAM assignment, built-in plug-in cards, hardware version, software

version PPC and DSP)



DISPLAY

(RAM assignment, USB stick memory capacity, display software version)

For a function check of the LEDs click LED TEST.
All LEDs on the front panel will light shortly.

For a complete reset of all parameters click RAM RESET.

Use

RAM RESET

only if there is no other possibility.

Before you confirm the reset, save all set parameters to the USB stick.

Loss of data!

If you perform RAM RESET, all set parameters will be lost!

Caution

ADVANCED
Shows advanced information about the MG3 Hot Bar.

«
...
21
22
23
24
25
...
»

Содержание MG3 Hot Bar


















































Отзывы:

Нет отзывов