manualshive.com logo in svg

Amada MG3 Hot Bar, Руководство по эксплуатации, Страница: 18 / 49

Поделиться
Скачать
Amada MG3 Hot Bar Скачать руководство пользователя страница 18

 

 

MG3 Hot Bar 

Operation 

76609576EN-MG3-HB-V1_0a.docx 18/49 
 

 

4.2

 

LED Status Display 

 

 

 

READY 

MG3 Hot Bar ready for measurement 

 

TRIGGER1 

Measurement activity on channel 1 

 

TRIGGER2 

Measurement activity on channel  2 

 

OVERFLOW 

MG3 Hot Bar overflow measuring range 

 

ACCEPT 

Measurement within set limits 

 

PREWARN 

 

Measurement outside set prewarn limits 

 

REJECT 

t

 

Measurement outside set limits 

 

USB 

  USB stick missing (blinking) or access to USB stick 

(on steady) 

 

4.3

 

Screen (Display) 

 

 

Fig.  5: Screen (Display) 

 

 1.

 

Display window quadrant 1 (Q1) 

2.

 

Display window quadrant 2 (Q2) 

3.

 

Menu bar 

4.

 

Program number selection 

5.

 

Button for single measurement 
(SINGLE) 

6.

 

Button for permanent 
measurement (RUN) 

7.

 

Button for logging (LOGGER) 

8.

 

Button for configuration menu 

(MENU) 

 

9.

 

Button for parameter 

overview (PARAM) 

10.

 

Button for analysis  

(LIMITS) 

11.

 

Shows current measuring 
mode 

(SINGLE/RUN) 

12.

 

Status bar for status, help 

and fault messages 

13.

 

Display window quadrant 4 

(Q4) 

14.

 

Display window quadrant 3 

(Q3) 

 

Содержание MG3 Hot Bar


















































Отзывы:

Нет отзывов