Alvarado SU5000 страница 11 Скачать руководство пользователя

Страница: 11 / 44

Supervisor 5000 Installation Instructions

PUD3667R1-6

For assistance: [email protected] +1 (909) 591-8431

Page 11

Cabinet Panel Removal

QA Checkpoint Shim Removal

It is assumed that the Pre-Installation Checklist steps are complete.

As part of our QA process, orange-colored shims

are inserted to set the correct gap for the electro-

mechanical brake. Remove these shims BEFORE

powering on the turnstile.
There is one (1) motor shim located in the master

cabinet; one (1) motor shim located in the slave

cabinet; and two (2) motor shims located in the center

cabinet (if applicable).

1. Remove each shim after the cabinet panel has

been removed by pulling firmly on the orange pull-

tab [Figure 7].

IMPORTANT

Pre-Installation Instructions

Cabinet Panel

Motor

Shim

(1 per motor)

Orange

Pull-Tab

Mounting Screws

1. Using a Phillips screwdriver, remove the six (6) mounting

screws that secure the cabinet panel to the master cabinet

[Figure 6]. Do not discard the cabinet panel screws as they

will be reused.

2. Once the screws are removed, gently slide the cabinet

panel out of position and set the panel off to the side

[Figure 6].

3. Repeat steps 1 and 2 to remove the slave cabinet panel.

Fig. 6

Fig. 7

Removing Screws

Removing Motor Shims

NOTE

Содержание SU5000













































Результаты поиска

Содержание SU5000

Отзывы:

Похожие инструкции для SU5000

Бренды по названию

Популярные бренды

Alvarado SU5000, Руководство по установке

Результаты поиска

Содержание SU5000

Отзывы:

Похожие инструкции для SU5000

Бренды по названию

Популярные бренды