manualshive.com logo in svg

Alvarado SU5000, Руководство по установке, Страница: 15 / 44

Поделиться
Скачать
Alvarado SU5000 Скачать руководство пользователя страница 15

Supervisor 5000 Installation Instructions

PUD3667R1-6 

       For assistance: [email protected]  +1 (909) 591-8431  

Page 15

Internal Card Reader Installation

Removing Status Light Board

Mounting the Card Reader

Routing the Output Cable

Routing the Output Cable

Output Cable 

(to Access 

Control 

System)

Fig. 15A

Fig. 15B

Mullion Style 

Card Reader

1.  Locate the card reader mounting bracket [Figure 13].
2.  Using a Phillips head screwdriver, remove the status light board 

[Figure 13].

3.  Using a Phillips head screwdriver, remove the three (3) 

mounting screws and remove the card reader mounting bracket.

4.  Install the card reader per manufacturer's instructions.

If the distance between the installed card reader and top channel 

lid exceeds the read range of the card reader, shims may be used 

to elevate the card reader by a maximum of 3/8" (9.5mm). 

DO NOT

 

allow the card reader to touch the status light board.
5.  Using a Phillips head screwdriver, insert and tighten three (3) 

mounting screws that secure the mounting bracket.

6. 

Place the status light board over the mounting standoffs 

and align the holes. Insert and tighten four (4) Phillips head 

mounting screws [Figure 14].

7.  Route the output cable through the turnstile and connect to your 

access control system. 

[Figure 15A & 15B].

Output cable must be routed down through the access hole. 
When removing and reattaching the card reader mounting 

bracket and status light board, make sure to re-seat and check 

all wire harnesses for damage.

Fig. 14

Fig. 13

Mounting 

Screws
Status Light 

Board

Mounting 

Bracket

Mounting 

Standoff

Card Reader

Output Cable

Access Hole

Exit Hole

NOTES

NOTE

(Status Light Board wire 

harnesses not shown)

(Status Light Board wire 

harnesses not shown)

Card readers used in connection with the site access control system 

are not included with the SU5000. The SU5000 has sufficient area for 

the installation of small mullion or slim style proximity card readers. 

Most card readers do not require separate power inputs. In the event 

that your reader requires a separate power input – do not pull this 

power from the SU5000 power supply. 
Due to the slim design of the SU5000, there is no space available to 

install circuit boards or other equipment associated with the access 

control system. Access control boards used in connection with the 

SU5000 are installed in locations exterior to the SU5000, in a wiring 

closet or other location. 

Содержание SU5000













































Отзывы:

Нет отзывов