TESTING AND COMMISSIONING
6.4 FACTORY RESET
The factory reset restores the settings that are set by default when the drive delivering. The con
figured positions of the door will be deleted. The recorded remote controls will be saved.
Tab/e 17
1
Press and hold the button IPR./(jfor about 5 secs to enter the
[il
programming mode
2
After the appearance of'Pl' inscription press the button IC../v)
§
3
After the appearance of'PO' inscription press the button
IST./
►I
n
4
After the appearance of'FO' inscription press the button
IST./
►I
n
After the appearance of'- -' inscription press and hold the button IST./►lfor
�
5
5 secs. A dot will appear on the display, this means the resetting to default
settings
6
To exit the programming mode press the button IPR./()twice or wait for
[D
15 secs (until automatic exit the setup menu). The display will show two dots
7.
TESTING AND COMMISSIONING
30
This is an important stage of drive system installation. The test is performed as follows:
• make sure that the requirements of section 1. 'General warnings and safety rules' and other
manual requirements are met in full.
• ensure stable and secure mounting of the drive and the guide rail.
• unblock the drive (section 4.2. 'Manual unblocking'). Manually open and close the door
several times. Make sure that there are no points of increased resistance to motion, and
there are no assembly and adjustment defects of the doors and drive. Return to the
blocked state.
• perform the full
open-close
cycle. Make sure, that the door moves in the required
directions, the leaf of the door moves smoothly. At the end of opening and closing the
door moves slowly.
• check the guide belt/chain tension degree and tighten if necessary
(fig.
19).
• make sure that the integrated LED backlight is functioning. lt is active when the door is
moving and for a set time after the door stops.
• check the correct working of the connected control devices (control buttons, remote
controls).
• check the correct working of each connected safety and alarm device (photocells,
movement stop devices, lamps etc.). Check the photocells for the absence of interaction
with other devices, to do so-close the optical axis: first close to TX photocell (transmitter),
then close to RX photocell (receiver) and then in the middle, between the two photocells.
Make sure that in all cases the drive properly reacts to the activation of photocells (during
closing the door stops and then fully opens).
• check the ability of the drive to identify the interaction with foreign objects du ring closing.
Put a 50 mm high obstacle on the floor. When the door contacts the obstacle during door
closing, the drive should stop the door and open completely.
LEVIGATO DRIVES (LG SERIES) LEVIGATO ANTRIEBE (SERIE LG) COMMANDES LEVIGATO (SERIE LG)
TECHNICAL MAINTENANCE
• check that du ring closing when you stop the doors with both hands, the doors stop and
then open. Du ring opening when you stop the doors with both hands, the doors stop.
Commissioning of the drive system can be done only after successful completion of tests. Partial
commissioning or temporary operation are forbidden.
Commissioning requires the installer to:
• prepare and keep technical documentation for the automation set. The documentation
shall include: general drawing, circuit layout, assembly and operation manual, as weil as
maintenance schedule.
• pass the filled 'Assembly and operation manual'to the user (owner).
• prepare the 'Maintenance schedule' and give it to the user (owner).
lnstruct about maintenance rules.
• instruct the owner about the existing hazards and risks, and inform about safe operation
rules. Explain to the owner the need to inform the persons operating the door about the
existing hazards and risks, and about safe operation rules.
8.
TECHNICAL MAINTENANCE
9.
&
Perform scheduled maintenance of the drive system to ensure efficient and safe operation.
Scheduled maintenance shall strictly comply with the existing regulatory documents, instructions
in this manual, instructions for other involved devices, and following the safety rules. Perform
scheduled maintenance at least once every six months.
Scheduled maintenance shall include:
• read the section 1. 'General warnings and safety rules'.
• check the wear of the set elements, paying attention to oxidization of the components.
Replace all parts and units with an unacceptable degree of wear. Use original parts from
the manufacturer.
• check the correctness of the door stop in its final positions. lf necessary, reprogram the final
positions.
• clean external surfaces of the drive and safety devices. Clean with the help of a soft moist
cloth. The use of the following for cleaning is forbidden: water jets, high pressure cleaners,
acids and alkali.
• perform the check according to the instruction in section 7. 'Testing and commissioning'.
TROUBLESHOOTING
ATTENTION!
In case of a failure, which cannot be repaired, based on the information
provided in this manual, consult the service department. Information about the service
department can be obtained from your supplier (vendor, installation company).
Drive does not work (the logo on
the drive is not lit; display does
not react, when buttons on the
front plate are pressed)
Drive is not control led by the
remote control (i ndicator on the
control is not lit)
..
No supply voltage or fuse
is blown
Remote control code is not
recorded in the drive control
unit memory
Tobte 18
Check the supply voltage.
Check, and if necessary, replace
the fuse (fuse parameters should
complywith the marking)
Record the remote control in the
drive memory
LEVIGATO DRIVES (LG SERIES) LEVIGATO ANTRIEBE (SERIE LG) COMMANDES LEVIGATO (SERIE LG)
31
