manualshive.com logo in svg

Altigen AltiWare ACM 5.2, Руководство администратора

Altigen AltiWare ACM 5.2 - высококачественное программное обеспечение для управления коммуникациями в вашем офисе. Скачайте бесплатное "Руководство администратора" для получения подробной информации о функциях и настройках. Скачать можно на {веб-сайте}.

Поделиться
Скачать
background image

Chapter 1:  Overview

4

AltiWare ACM 5.2 Administration Manual

•

SIP Extension Home Gateway Assignment 

- This feature affects only multi-

chassis installations. The primary purpose of this feature is to allocate resources for 
the IP phone when conferencing, silent monitoring, barging-in, and conversation 

recording. This allows the administrator to configure sufficient VoIP resources in an 
AltiGateway chassis for IP phone users assigned to this home AltiGateway. 

•

SIP Trunk Support 

- An increasing number of service providers offer dial tone 

through data network using SIP protocol. Beginning with Release 5.1, AltiWare 
enables AltiGen’s system to connect to IP-based trunking service providers via SIP. 

•

SIP IP Phone (IP600, IP710, IP705)

 - Through firmware upgrade, all AltiGen IP 

phones can run SIP protocols.

•

SIP NAT Traversal

 - This feature allows AltiWare to connect to a remote SIP phone 

or IPTalk behind NAT without changing the NAT setting at the remote location.

•

Support for RFC 2833 (DTMF payload embedded with RTP) 

- Supported in SIP 

trunks only. This feature helps to resolve DTMF tone detection and regeneration 

when using G.723.1 or G.729 codec. Basically low bit rate compression will distort 
DTMF tone during compression. The far end device may not be able to recognize the 
DTMF digits. RFC 2833 specifies a separate RTP payload format to carry DTMF 

information to ensure the other side can recognize the tone properly.

•

Support for both SIP and H.323 Tie Trunk 

- When setting up a system-to-system 

VoIP tie trunk, either SIP or H.323 protocol can be used.

Multi-Site Enterprise Management - AltiEnterprise Manager

•

Replaces DINA Manager and IP Dialing Table in 5.0A

•

VoIP domain 

- When networking multiple AltiGen systems from different sites, one 

system can be assigned as the VoIP domain controller to propagate configuration 
data to member systems.

•

Directory Synchronization

 - When a new extension is added to one of the member 

systems and configured as a Global extension, the VoIP domain controller will 
propagate this extension to all member systems. Every member system within the 

VoIP domain can see the extension number plan of the other systems.

•

Multi-site Call Routing

 - When a user dials an extension number which is not a 

local extension number, the system searches the Domain extension list. If a list is 
found, the system will dial the number by using the IP address and extension 
number stored in the Domain extension list.

•

Domain User Management

 - VoIP domain controller can resolve the conflict if 

duplicated extension numbers are created in different member systems. This feature 

also manages extension relocation. When an extension user is relocated to another 
member system, its voice mail and greeting can be relocated as well.

•

Global Least Cost Routing 

- When multiple systems are in different area codes or 

countries, the administrator can set up Global Least Cost Routing to route long 
distance or international calls through member systems. The routing rules are 

propagated to all members automatically.

•

Global IP Dialing Table 

- In the 5.1 Release, the IP Dialing Table moved to 

AltiEnterprise Manager. The IP Dialing Table configuration is used to create location-
based routing in the AltiEnterprise. Beginning with Release 5.1, the IP Dialing Table 
supports hop-off blocking by location to prevent unnecessary hop-off calling.

Содержание AltiWare ACM 5.2





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AltiWare ACM 5.2

Casio EMULATOR FX-ES User Manual preview
EMULATOR FX-ES
Бренд: Casio Страницы: 18
ViewSonic MultiView Datasheet preview
MultiView
Бренд: ViewSonic Страницы: 2
Lowrance 6.2 Installation And Operation Instructions Manual preview
6.2
Бренд: Lowrance Страницы: 80
Lowrance 6.3 Installation And Operation Instructions Manual preview
6.3
Бренд: Lowrance Страницы: 108
VMware VSHIELD APP 1.0.0 UPDATE 1 - API Admin Manual preview
VSHIELD APP 1.0.0 UPDATE 1 - API
Бренд: VMware Страницы: 144
UNIBLUE PowerSuite 2010 Product Manual preview
PowerSuite 2010
Бренд: UNIBLUE Страницы: 13
Cabletron Systems SEHI-22/24 User Manual preview
SEHI-22/24
Бренд: Cabletron Systems Страницы: 90
MACROMEDIA COLDFUSION MX-CLUSTERCATS Use Manual preview
COLDFUSION MX-CLUSTERCATS
Бренд: MACROMEDIA Страницы: 156
IBM PERFORMANCE MANAGEMENT FOR POWER SYSTEMS - INTERACTIVE GRAPHING SUPPORT FOR ... Manual preview
PERFORMANCE MANAGEMENT FOR POWER SYSTEMS - INTERACTIVE GRAPHING SUPPORT FOR ...
Бренд: IBM Страницы: 29
Microtek ScanMaker X6 EPP User Manual preview
ScanMaker X6 EPP
Бренд: Microtek Страницы: 15
Microtek ScanPotter Reference Manual preview
ScanPotter
Бренд: Microtek Страницы: 36
TC Electronic MegaReverb Manual preview
MegaReverb
Бренд: TC Electronic Страницы: 7
iHome iA5 Start Manual preview
iA5
Бренд: iHome Страницы: 22
Samsung Universal Print Driver 2 User Manual preview
Universal Print Driver 2
Бренд: Samsung Страницы: 15
Lenovo THINKPAD T40P Manual preview
THINKPAD T40P
Бренд: Lenovo Страницы: 100
Lenovo THINKPAD T41 Setup Manual preview
THINKPAD T41
Бренд: Lenovo Страницы: 6
Xerox DocuSP Brochure preview
DocuSP
Бренд: Xerox Страницы: 2
Oki C3200n Manual preview
C3200n
Бренд: Oki Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды