Altigen AltiWare ACC 5.2 Скачать руководство пользователя

Страница: 380 / 399

368

AltiWare ACC 5.2 Administration Manual

DNIS, Caller ID:

•

DTMF (Dual Tone Multi-Frequency)

Physical Termination:

•

RJ-48X or RJ-48C

Wire:

•

4 wires

800 Service:

•

You decide

Termination Impedance:

•

100 ohms

Type of Registered Services Provided

•

BN 1.544 Mbps SF without power

•

DN 1.544 Mbps SF B8ZS without power

•

1KN 1.544 Mbps ANSI ESF without power

•

1SN 1.544 Mbps ANSI ESF, B8ZS without power (recommended)

Service Order Code

SOC 6.0P AS.2

T1 Channel Assignment

•

Trunk Type

—

In, Out, or 2-Way (recommended)

•

Channels Assigned

—

24 (Enter partial channels if you wish to subscribe to both voice

and data service.)

•

Hunting

—

Most Idle, Least Idle, Ascend, Descend

•

DNIS Digits/Signal

—

3/DTMF (can be 3 to 10 digits)

•

Caller ID Signal

—

DTMF, if available (Not every service provider provides Caller ID

over T1 lines.)

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk line coming in
from the phone company to the PBX. A CSU can terminate signals, repeat signals and
respond to loopback commands sent from the central office.

Содержание AltiWare ACC 5.2
















































































































































































































































































































































































































Результаты поиска

Содержание AltiWare ACC 5.2

Отзывы:

Похожие инструкции для AltiWare ACC 5.2

Бренды по названию

Популярные бренды

Altigen AltiWare ACC 5.2, Руководство администратора

Результаты поиска

Содержание AltiWare ACC 5.2

Отзывы:

Похожие инструкции для AltiWare ACC 5.2

Бренды по названию

Популярные бренды