Altigen AltiWare ACC 5.2 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 399

Altigen AltiWare ACC 5.2 Скачать руководство пользователя страница 128

Chapter 11: Board Configuration

116

AltiWare ACC 5.2 Administration Manual

Configuration

Double-click the TritonIP board in the

Boards

window to open the

Board Configuration

window, similar to Figure 2 on page 112. See attribute descriptions below Figure 2. Note
the following additional information:

•

Clicking the

Board Configuration

button opens a window that displays the board

serial number, DSP clock, and physical and logical IDs. The drop-down list in the

Configure Type

field lets you select between a 12-port G.711/G.723/G.729

configuration and a 30-port G.711 configuration.

Figure 5. Board Configuration window

Configuring the Triton T1/E1 Board

Through AltiWare Administrator, the Triton T1/E1 board can be configured for either
digital T1 CAS (channel associated signaling), T1 PRI (Primary Rate Interface), E1 CAS,

or E1 PRI.
Both T1 CAS and T1 PRI carry 24 channels using time-division multiplexing (TDM) at an
overall rate of 1.544 Mbps. Voice T1 provides 24 64K channels with robbed bit signaling.
T1 PRI provides 23 64K channels, using one 64K channel for D channel messaging.
E1 CAS and E1 PRI carry 32 channels using TDM at an overall rate of 2.048 Mbps. Both

of them provide 30 64K channels for voice.
To subscribe to T1 CAS, T1 PRI, E1 CAS, or E1 PRI service, you must supply certain
parameters. These parameters are listed in Appendix B on page 367.

Configuring the Board

Double-click the Triton T1/E1 board in the

Boards

window to open the

Board

Configuration

window, similar to Figure 2 on page 112. See attribute descriptions

below Figure 2. Note the following additional information:

•

The Board ID must be in the range 0–7.

•

Double-click a channel in the

Channel Mapping List

to open a trunk configuration

dialog box.

•

Double-click a channel group to open a configuration window, discussed in the
following section.

•

Clicking the

Board Configuration

button opens a configuration dialog box that

displays the board’s serial number, DSP clock, physical and logical IDs.

If you change this configuration,
you must restart the switching
services for the change to take
effect.

«
...
126
127
128
129
130
...
»

Содержание AltiWare ACC 5.2
















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды