Altigen AltiWare ACC 5.2 Скачать руководство пользователя | Manualshive

Страница: 167 / 399

background image

Chapter 12: Trunk Configuration

AltiWare ACC 5.2 Administration Manual 155

Figure 13. Setting trunk In Call Routing to an AA

5. Call from one trunk to the testing reference trunk. You should hear a 1kHz tone

playing at the originating side.

6. While the tone is playing, measure the Rx Level at the trunk that is making the

outgoing call.
If the reading is less than -6 dB, for example -3 dB, take the following steps to
attenuate the gain for the Triton Analog Trunk to IP phone connection:
a. Go to VoIP Board configuration and click the

Advance

button.

b. Set the Transmitting gain to IP Extension to 3 for the Triton Analog Trunk. (Do

NOT change the gain in the trunk property of the Triton Analog Trunk Board,

since it may impact the echo canceller performance. If the reading is -6 dB to -
14 dB, for example, -12dB, no change is needed.

If the reading is -15 dB to -18dB, take the following steps to increase the gain for
the Triton Analog Trunk to IP phone connection:
a. Go to VoIP Board configuration and click the

Advance

button.

b. Set the Transmitting gain to IP Extension to 9 for the Triton Analog Trunk. (Do

NOT change the gain in the trunk property of the Triton Analog Trunk Board,

since it may impact the echo canceller performance.)

«
...
165
166
167
168
169
...
»

Содержание AltiWare ACC 5.2
















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AltiWare ACC 5.2

CORPORATE SUITE

Бренд: KAPERSKY Страницы: 36

RayTech RNS 5.0

Бренд: Raymarine Страницы: 152

Бренд: MACROMEDIA Страницы: 830

CLUSTER SUITE - FOR RHEL 4

Бренд: Red Hat Страницы: 74

SYSMAC CX-Programmer 9

Бренд: Omron Страницы: 232

CERTIFICATE SYSTEM 7.2 - MIGRATION GUIDE

Бренд: Red Hat Страницы: 512

Бренд: Tascam Страницы: 210

Бренд: Vonamic Страницы: 30

Doctor Pro TM-2430-13

Бренд: A&D Страницы: 69

Application Accelerator

Бренд: Intel Страницы: 90

05720-017408-9621 - AE AUTOCAD LT 2000I LAB-PK 10U CD

Бренд: Autodesk Страницы: 21

00128-051462-9340 - AutoCAD 2008 - PC

Бренд: Autodesk Страницы: 48

Instrument Driver NI-DMM

Бренд: National Instruments Страницы: 12

Бренд: HP Страницы: 173

Бренд: HP Страницы: 20

-UX B6941-90001

Бренд: HP Страницы: 548

Бренд: Waves Страницы: 40

Бренд: Oki Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды