manualshive.com logo in svg

Alpha Professional Tools VSP-120, Инструкция по эксплуатации

Поделиться
Скачать
Alpha Professional Tools VSP-120 Скачать руководство пользователя страница 6

4

  

CAUTION

The  following  are  important  notes  for  products,  operation,  and  maintenance 

applicable to this polisher.

GENERAL SAFETY RULES

wOrK ArEA

• 

 Keep your work area clean and well lit.

  Cluttered benches and dark areas 

invite accidents.

• 

 Do not operate power tools in explosive atmospheres, such as in the 

presence of flammable liquids, gases, or dust.

  Power tools may create 

sparks which may ignite the dust or fumes.

•   Keep bystanders, children, and visitors away while operating a power 

tool.

 Distractions can cause you to lose control.

ELECTriCAL SAFETY

• 

 

Grounded tools must be plugged into an outlet properly installed and 

grounded in accordance with all codes and ordinances. 

Never remove the 

grounding prong or modify the plug in any way. Do not use any adaptor plugs. 

Check with a qualified electrician if you are in doubt as to whether the outlet is 

properly grounded. If the tools should electrically malfunction or break down 

grounding provides a low resistance path to carry electricity away from the user.

•   Avoid body contact with grounded surfaces, such as pipes, radiators, 

ranges, and refrigerators.

 There is an increased risk of electric shock if your 

body is grounded. Don’t expose power tools to rain or wet conditions. Water 

entering a power tool will increase the risk of electric shock.

• 

 

Do not abuse the cord.

 Never use the cord to carry the tools or pull the plug 

from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. 

Replace damaged cords immediately.  Damaged cords increase the risk of 

electric shock.

• 

 

When operating a power tool outside, use an outdoor extension cord 

marked “W-A” or “W”

. These cords are rated for outdoor use and reduce 

the risk of electric shock.

PErSONAL SAFETY

• 

 

Stay  alert,  watch  what  you  are  doing  and  use  common  sense  when 

operating a power tool.

  Do not use tool while tired or under the influence of 

drugs, alcohol, or medication.   A moment of inattention while operating power 

tools may result in serious personal injury.

Содержание VSP-120





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды