Alpha Professional Tools VSP-120 Скачать руководство пользователя страница 34

Страница: 34 / 36

iii

Can I use the VSP-120 for drilling applications such as

faucet

holes?

Yes. The VSP-120 can be used with Alpha® Core Bits to drill
faucet mounting holes. we recommend using the provided

C-Handle attachment and a template.

How many gallons of water does the Alpha® VSP-120 use per minute?

The Alpha® VSP-120 has a throughput of approximately 1.1 gallons

per minute with the water valve fully open.

HELPFUL HINTS

If your VSP-120 does not start, check the carbon brushes for proper
seating.

If the VSP-120 does not re-start, check and reset the GFCI.

Avoid dragging the VSP-120 on top of stone surfaces. The aluminum
body may leave marks on the surface.

The C-Shape handle attached to the polisher is highly recommended for
more stability of the polisher during certain applications such as: surface
polishing, core drilling and proﬁling.

Содержание VSP-120





































Результаты поиска

Содержание VSP-120

Отзывы:

Бренды по названию

Популярные бренды

Alpha Professional Tools VSP-120, Инструкция по эксплуатации

Результаты поиска

Содержание VSP-120

Отзывы:

Бренды по названию

Популярные бренды