PAGE 51
ALMAC s.r.l.
2.4
Provisions and prohibitions and general rules on safety and use of the platform
•
Read this manual carefully before starting, using, servicing or performing other operations on
the machine;
•
The MEWP must always be kept in perfect conditions by following the maintenance program
described in the
Maintenance Chapter
;
•
Do not wear rings, wrist watches, jewellery, unfastened or loose clothing such as neck ties,
torn garments, scarves, unbuttoned jackets or garments with open zip fasteners that could get
caught up in moving parts;
•
Wear approved safety garments, such as non-slip footwear and a reflective vest;
•
To lower the slipping or tripping risk to the minimum, always keep the operator compartment,
platform surfaces, steps, handrails and grip bars clean and free from all foreign objects or
traces of oil, mud and snow;
•
Clean the soles of your footwear before getting on the M.E.W.P.
•
THE OPERATOR MUST NOT MOVE BETWEEN THE BASKET AND A STRUCTURE EXTERNAL TO
THE MACHINE AS THE STABILITY CONDITIONS OF THE MACHINE MAY BE EXCEEDED;
•
THE STAFF AND EQUIPMENT MUST ONLY ENTER AND EXIT THE BASKET WITH THE PLATFORM
IN THE TRANSPORT POSITION. IT IS FORBIDDEN TO LOAD OR UNLOAD THE PLATFORM WHEN
IT IS ELEVATED;
•
Do not use the controls or flexible hoses as hand grips;
•
Do not lean over the perimeter railings of the basket;
•
Inform the maintenance managers of any irregularities in operation;
•
Make sure that all guards and other protections are positioned correctly and that all the safety
devices are installed and efficient;
•
Do not use the platform in places where there is a risk of explosion or fire outbreaks;
•
Do not use water jets or high pressure washers to wash the platform;
•
The operator on the platform, according to the current accident-prevention regulations,
must
use a protective HELMET and connect the appropriate SAFETY HARNESS secured to the support
of the basket. The operator on the ground must also wear a hard-hat;
•
USE OF THE PLATFORM ALWAYS REQUIRES AT LEAST 2 OPERATORS, ONE OF WHOM IS ON
THE GROUND and able to perform the emergency operations described in this Manual;
•
The platform must not be used if there is insufficient light, as it is not fitted with its own
lighting on board;
•
In case of rain, be certain to protect the control box in the basket using the dedicated cover;
•
Keep a distance of at least 2 m from marked differences in height (ditches, steep terrain,
etc.);
•
Ensure there is sufficient autonomy to avoid the forced shutdown of the machine;
•
It is forbidden to use the platform to lift loads;
•
Overloads, transverse stresses, impacts, brusque and sudden movements of the platform are
forbidden;
•
Abrupt movements on the platform are not permitted;
•
When moving or working on the platform, both feet must be firmly placed on the floor of the
basket;
•
Never walk on the boom to access the basket or to leave it;
•
It is forbidden to get on or off the platform while it is being controlled from the ground;
•
It is forbidden to remove protective covers (except for maintenance operations);
•
It is forbidden to operate near high voltage aerial power lines and in any case the work platform
must always remain at a minimum safety distance of 5 m from cables. For voltages greater
than 132KV proceed as shown in the table below;
Содержание AlmaCrawler JIBBI 1250 EVO
