Allied Telesis AT-ANC10S Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 124

Allied Telesis AT-ANC10S Скачать руководство пользователя страница 49

AT-ANC10S/2 Adapter Installation and User’s Guide

49

Installing the Windows Driver Software

This chapter describes how to install all of the following Windows
Operating Systems:



Microsoft Windows Server 2008 (32-bit and 64-bit extended)



Microsoft Windows Server 2008 R2



Microsoft Windows Server 2012 and 2012 R2

The Windows driver software for all of the Windows Operating Systems is
available on the Allied Telesis website at

www.alliedtelesis.com/

support/software

. After you have accessed this website, enter the model

number in the

Search by Product Name

box and then click

Find

to

display the current list of software drivers.

There are two methods to install the software drivers on all of the Windows
Operating Systems: the Installer and Silent installation. The Installer uses
a graphical interactive mode. The Silent Installation is a command-line
interface for unattended installation. See the following sections:



“Using the Installer” on page 50



“Using Silent Installation” on page 54

Note

These instructions are based on the assumption that your adapter
was not factory installed. If your controller was installed at the
factory, the driver software has been installed for you.

Note

Before installing the driver software, verify that the Windows
operating system has been upgraded to the latest version with the
latest service pack applied.

Note

You must physically install a network device driver before the AT-
ANC10S/2 network adapter can be used with your Windows
Operating System. There is no installation CD. You must download
the drivers from the Allied Telesis website at

www.alliedtelesis.com/support/software

. After you have

accessed this website, enter the model number in the

Search by

Product Name

box and then click

Find

to view the current list of

documents and drivers.

«
...
47
48
49
50
51
...
»

Содержание AT-ANC10S





























































































































Отзывы:

Нет отзывов