ALLIANCE X Скачать руководство пользователя страница 6

Страница: 6 / 76

201143

Safety Information

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the washer is properly grounded.

W003

WARNING

Repairs that are made to your products by unqualified persons can result in hazards due to

improper assembly or adjustments subjecting you, or the inexperienced person making such

repairs, to the risk of serious injury, electrical shock, or death.

W007

WARNING

If you or an unqualified person perform service on your product, you must assume the

responsibility for any personal injury or property damage which may result. The manufacturer

will not be responsible for any injury or property damage arising from improper service and/or

service procedures.

W008

WARNING

Содержание X













































































Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды

ALLIANCE X, Руководство по устранению неисправностей

Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды