ALLIANCE X Скачать руководство пользователя страница 50

Страница: 50 / 76

201143

Adjustments

28. Pressure Switch

Refer to

Figure 2

NOTE: DO NOT ADJUST PRESSURE SWITCH

IF WASHER IS WITHIN THE WARRANTY

PERIOD.
Pressure switch is set at the factory for proper water

fill levels. However, if there is a problem of

overfilling or underfilling, pressure switch can be

adjusted.

Maximum water fill level can be increased by

turning adjusting screw

CLOCKWISE

, and

decreased by turning screw

COUNTERCLOCKWISE

One quarter turn of the adjusting screw represents

approximately one inch (25.4 mm) increase or

decrease of water level in washtub.

IMPORTANT:

DO NOT

turn adjusting screw more

than 3/4 of a turn in either direction as the switch

may be damaged and flooding could result.
When testing, pressure switch has continuity from

terminal 1 to 2 when empty and 1 to 3 when full.

29. Belt (Agitate And Spin)

No belt adjustment is required.

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the washer is properly grounded.

W003

WARNING

Figure 2

W457SE1B

Adjusting

Screw

Содержание X













































































Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды

ALLIANCE X, Руководство по устранению неисправностей

Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды