ALLIANCE X Скачать руководство пользователя страница 52

Страница: 52 / 76

201143

Test Procedures

NOTE: Resistance readings slightly out of given

ranges may be due to meter conditions. These

readings DO NOT necessarily indicate motor

failure.

NOTE: Steps 8, 9 and 10 are with motor centrifugal

mechanism in the run position.

Meter Connections

Reading

Should Be

If Not

Ground to Each Other Terminal

Open

Terminal shorted to ground.

White to Yellow

Closed

Open thermal overload.

Red to Brown

2-8 Ohms

Start winding open or resistance too high or too low.

Blue to White

1-2 Ohms

High speed winding (4 pole) open or resistance too
high or too low.

Violet to White (2-speed motor)

2.5 Ohms

(Approximate)

Low winding opening; High speed winding open; or
resistance too high or too low.

“R” to Red

Closed

Open start (auxiliary) switch.

“P” to Blue (2-speed motor)

Closed

Open start switch 4 pole winding.

“R” to Red

Open

Start auxiliary switch.

“P” to Blue (2-speed motor)

3 Ohms

(approximate)

Refer to Blue to White and Violet to White.

10.

“P” to Blue (2-speed motor)

Closed

Open low (6 pole) winding run switch.

Содержание X













































































Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды

ALLIANCE X, Руководство по устранению неисправностей

Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды