ALLIANCE X Скачать руководство пользователя страница 16

Страница: 16 / 76

201143

Section 3

General Troubleshooting

IMPORTANT: Refer to Wiring Diagram for aid in testing washer components.

1. Clicking Noise During Operation on NEWLY Installed Units

If a clicking noise is heard when first starting up a new

topload washer, the noise is related to the belt taking a

temporary “set” around the idler pulley. The set causes

a slight bump in the belt which in turn causes the idler

lever to tap the motor bracket making the clicking

noise. THE BELT DOES NOT NEED TO BE

REPLACED.

To correct this condition please perform the following

break-in procedure:

After installing the unit start a fill cycle to

make sure the seals have been lubricated.

Stop the fill cycle and place the unit into a

spin cycle.

Run the cycle for several minutes until the

belt has warmed up. This will remove the

“set.”

Normal use will keep the belt from

resetting.

For extended periods of non-use (three to

four weeks), this procedure might need to

be repeated.

WARNING

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the washer is properly grounded.

W003

Содержание X













































































Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды

ALLIANCE X, Руководство по устранению неисправностей

Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды