ALLIANCE X Скачать руководство пользователя страница 19

Страница: 19 / 76

201143

General Troubleshooting

4. No Cold Water

There is no cold
water.

Is the water

supply faucet

closed?

Open faucet.

Yes

Is the cold

water fill hose

kinked?

Straighten or

replace hose.

Yes

Is the mixing valve

screen or screen in

outer end of fill hose

nearest water supply

faucet clogged?

Disconnect
cold fill hose
and clean or
replace screen.

Yes

Is cold water

mixing valve

solenoid

inoperative?

Test
solenoid
and
replace if
necessary.

Yes

Is temperature

switch

inoperative?

Test switch
and replace if
inoperative.

Yes

Is pressure

switch

inoperative?

Test switch.
Must have
continuity from
terminal 1 to 2
when empty or
1-3 when full.
Replace if
inoperative.

Yes

Is pressure

hose

clogged?

Remove and
clean or
replace hose.

Yes

Is there

broken, loose

or incorrect

wiring?

Refer to
appropriate
wiring
diagram.

Yes

TLW410S

Is unit plugged in

and power

available to outlet?

Check plug
and reset
circuit
breaker.

Yes

timer/control

inoperative?

Test for
continuity
through timer
circuits (refer to
wiring diagram)
or test control
and replace if
inoperative.

Содержание X













































































Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды

ALLIANCE X, Руководство по устранению неисправностей

Результаты поиска

Содержание X

Отзывы:

Похожие инструкции для X

Бренды по названию

Популярные бренды