manualshive.com logo in svg

Alliance Laundry Systems LES19A SERIES, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems LES19A SERIES Скачать руководство пользователя страница 46

505692

47

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

46. CYLINDER ROLLERS

a. While supporting the access panel, remove two 

screws from bottom edge of access panel. See 
Figure 5.

b. Gently lower the access panel to disengage 

locators from bottom edge of front panel. See 
Figure 12.

c. Remove two screws holding bottom tabs on 

front panel to dryer side panels. See Figure 12. 
Swing bottom of front panel away from dryer 
far enough to disengage hold-down clips and 
locators from cabinet top.

d. Disconnect wires from door switch. See 

Figure 11.

NOTE: Refer to wiring diagram when rewiring 
switch.

e. Disengage belt from motor and idler pulleys. 

See Figure 19.

f. Remove four screws holding bulkhead to front 

flange of cabinet. Then lift complete bulkhead 
assembly out of slots in cabinet. See Figure 25.

IMPORTANT: When reassembling, be sure seal on 
exhaust fan cover makes airtight seal on flange of 
duct. See Figure 16. If the seal is installed 
improperly, the airflow through the exhaust system 
will be restricted which can adversely affect dryer 
performance.

g. Pull cylinder forward allowing rear of cylinder 

to drop down exposing rollers. See Figure 31.

h. See Figure 31 for removal of roller from 

bulkhead.

NOTE: When replacing the cylinder roller, it is 
important that cylinder roller is installed with the 
flanged surface of the roller bearing facing towards 
the front of the dryer.

47. OUTLET COVER

NOTE: Outlet cover is not removable from the 
heater duct assembly that originally came with the 
dryer. It is only removable from the replacement 
heater duct assembly, Part No. 503607P.

a. Open door and remove two screws holding 

outlet cover to heater duct assembly. See 
Figure 30.

To reduce the risk of serious injury or death 
by carbon monoxide and other gases in gas 
dryers, carefully read and follow all 
instructions given in this section.

W005

WARNING

Figure 31

ROLLER

BRACKET

SHAFT

SCREW

RETAINER

RING

FLANGED SURFACE

OF ROLLER BEARING

(Must face towards front of dryer)

LOCKNUT

WASHERS

REAR

BULKHEAD

D260SE1A

Содержание LES19A SERIES



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды