manualshive.com logo in svg

Alliance Laundry Systems LES19A SERIES, Руководство по обслуживанию, Страница: 51 / 66

Поделиться
Скачать
Alliance Laundry Systems LES19A SERIES Скачать руководство пользователя страница 51

52

505692

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

50. CABINET

a. Remove the three screws holding the control 

assembly to the control hood rear panel. See 
Figure 4.

b. Rotate the assembly forward to access inner 

wiring.

c. Disconnect wiring from inner components and 

carefully remove components from control 
hood assembly.

NOTE: Refer to wiring diagram when rewiring 
component parts.

d. Rotate control hood assembly forward and lift 

to free assembly from hold-down clips.

e. Remove two screws from bottom edge of lower 

front access panel. See Figure 5.

f. Swing bottom of panel away from dryer to 

disengage hold-down clips and locators from 
bottom edge of front panel.

g. Remove two screws holding bottom tabs on 

front panel to dryer side panels. See Figure 5. 
Swing bottom of front panel away from dryer 
far enough to disengage hold-down clips and 
locators from cabinet top.

h. Disconnect wires from door switch. See 

Figure 11.

NOTE: Refer to wiring diagram when rewiring 
switch.

i. Remove two cabinet top hold-down screws. 

See Figure 24.

j. Lift cabinet top to a vertical position by hinging 

it on the rear hold-down brackets. See 
Figure 24.

NOTE: Cabinet top may be raised and hinged on 
the rear hold-down hinges or supported against 
wall behind dryer while servicing.

k. Carefully withdraw wire harness through hole 

in cabinet top and lift the top off the hold-down 
brackets. See Figure 24.

l. Disengage belt from motor and idler pulleys. 

See Figure 19.

NOTE: When reinstalling belt, be sure belt is 
properly installed on motor and idler pulleys and is 
on the correct side of the idler lever. See Figure 19. 
Belt must be positioned around cylinder between 
center and rear baffle screws with the ribbed 
surface against the cylinder. After installing belt, 
manually rotate cylinder counterclockwise to check 
that belt is properly aligned.

m. Remove four screws holding bulkhead to front 

flange of cabinet and lift complete bulkhead 
assembly out of slots in cabinet. See Figure 25.

n. Carefully remove cylinder out through front of 

dryer.

Содержание LES19A SERIES



































































Отзывы:

Нет отзывов