allen AW16-K 2019 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 62

allen AW16-K 2019 Скачать руководство пользователя страница 58

Cleaning Procedure

Machine Cleaning Procedure

When cleaning the machine, please adhere to the following information to ensure proper cleaning and to
keep the machine in the best condition possible.

Power Washing Procedure:

•  Ensure that the water pressure is below 2000 PSI (14 MPa)
•  Always keep the water temperature below 180°F (80°C)
•  Use a spray nozzle with at minimum 40° wide spray angle
•  Keep the nozzle at least 1 foot (300mm) away from the machine
•  Avoid spraying water on the engine and electronic components. Examples include electronic displays,

lights, switches, wiring, etc. The electronic components may be damaged if water is sprayed on them.

• Keep a perpendicular angle (90°) when cleaning over a decal.

- Holding nozzle of a pressure washer at an angle different from 90° may lift the

decal from the machine.

• Recommended using a safe cement dissolver,

BACK-SET

or similar

,

to remove

hardened concrete.

• It is

NOT

recommended to use chemicals such as:

- Muriatic Acid

- Hydrochloric Acid

- Hydrofluoric Acid

- Sulfuric Acid

- Phosphoric Acid

• To prevent build-up of concrete on the machine, use

BODY GUARD

or similar protection wax.

Filter Cleaning Procedure:

• Remove air filters and blow out with compressed air,

NOT

to exceed 80 PSI.

SECTION 3

SERVICE

069583

Page 58

«
...
56
57
58
59
60
...
»

Содержание AW16-K 2019































































Отзывы:

Нет отзывов