allen AW16-K 2019 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 62

background image

Driving Equipment

Ø

The Directional Control Lever (located on the top right side of the dash) controls the direction of travel - forward,

reverse and neutral (free-wheeling). Select the direction of travel desired. The Speed Control Lever (located on the
right side of the handle bar) controls the vehicle speed, power, and dynamic hydraulic braking.

IMPORTANT OPERATOR NOTE: When starting from a stop, steadily pull the Speed Control Lever towards the hand
grip. The more the Speed Control Lever is squeezed towards the hand grip the faster the buggy will move. Position
the Speed Control Lever where the engine does not lug to achieve maximum speed or power depending on job site
conditions. Do not use the engine rpm speed to control buggy speed. Letting the Speed Control Lever return to the
neutral position will slow the buggy (by means of dynamic hydraulic braking) and increase power at the drive wheels,
acting as a “downshift”

Ø

To slow and/or stop vehicle:

• Release Speed Control Lever.

• Service brake pedal (located at right of stand-on platform) may be pushed down to acti-

vate service brake and assist in slowing the vehicle.

• Avoid sudden stops whenever possible.

In all cases, upon release of the speed control lever, the speed control linkage should operate smoothly and

freely and completely stop machine travel within 6’ – 8’ in both forward and reverse. If the speed control

linkage does not operate smoothly and freely and/or does not automatically stop machine travel upon

release of the speed control lever, then remove machine from service until repairs have been made.

Operating Instructions

SECTION 2

OPERATIONS

069583

Page 33

«
...
31
32
33
34
35
...
»

Содержание AW16-K 2019































































Отзывы:

Нет отзывов

Похожие инструкции для AW16-K 2019

Бренд: Eagle Страницы: 166

Бренд: U-Line Страницы: 4

Бренд: CanyCom Страницы: 66

Бренд: Jet Страницы: 12

Kenworth T170 2011

Бренд: Paccar Страницы: 179

Бренд: GMC Страницы: 386

Бренд: Landoll Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды