allen AW16-K 2019 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 62

allen AW16-K 2019 Скачать руководство пользователя страница 51

Hydraulic Drive/Bucket Dump:

• Check hydraulic oil level daily. Check oil level with bucket in the “down” position, and with oil temperature cold.

Fill reservoir to bottom of bolt head on filler cap or “F” mark on dipstick with SAE 10W-40 weight SE motor oil.
Reservoir capacity is 18.7 quarts.

• Replace hydraulic oil and hydraulic oil filter every 200 hours or 6 months, whichever occurs first. Drain oil from

hydraulic reservoir by disconnecting hose item 28, from elbow fitting item 45.

• Inspect all hydraulic hoses & fittings daily. Repair or replace as required.

Chassis Lubrication

Lubricate all machine points per the following schedule:

Brake

Inspect both service brake and parking brake lock DAILY. Parking brake must hold a loaded buggy on 15% grade
(8.5 degrees). Service brake must lock both drive wheels of a loaded buggy when brake pedal is applied while buggy
is in motion. If adjustment is required to bring brake operation up to these specs, refer to pages ??? for adjustment
procedures.

Maintenance

SECTION 3

SERVICE

069583

Page 51

«
...
49
50
51
52
53
...
»

Содержание AW16-K 2019































































Отзывы:

Нет отзывов