allen AW16-K 2019 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 62

allen AW16-K 2019 Скачать руководство пользователя страница 20

Ø

The engine on this machine may be equipped with an exhaust purifier that may reduce,

but will not eliminate

these dangerous emissions.

Ø

The efficiency of this purifier decreases if the engine is not properly tuned, especially if the fuel mixture is too

rich. Do not modify the stock Kohler fuel/air ratio. If this machine is to be operated regularly at altitudes higher than
6,000 feet above sea level, see the engine manual for additional information. Excessive exhaust temperatures above
1200F (649C) will damage the purifier.

Ø

The exhaust purifier is

extremely hot

. Do not touch. Keep all flammable material at least 10 feet away. Avoid fuel

spills. Allow engine to cool at least 20 minutes before refueling.

Ø

Do not operate this equipment on unsafe haul roads, load areas or dump areas. This

equipment is intended for use only on well lit, leveled and compacted surfaces

. AVOID

ALL CONDITIONS OF SLOPE AND/OR GRADE, WHICH MAY CAUSE THIS EQUIPMENT TO TIP.

Never operate this equipment on any grade or slopes greater than 15% (8 degrees), less if site conditions so warrant.
Verify that all haul roads, load and dump areas will safely support this vehicle with maximum payload. Operating this
buggy on rough, uneven surfaces will cause the steering wheels to jerk and make it difficult for the operator to steer.
All haul roads must have a suitable surface for good footing for the operator. Wet, muddy and/or loose surfaces may
cause an operator to lose his footing and fall.

Do not operate this equipment in poorly lit areas

. Provide artificial

lighting as required for safe operation.

Ø

Do not operate this machine under the influence of drugs and/or alcohol

.

Ø

Identify all unprotected openings on job site and do not operate this equipment near these openings.

Ø

Identify all overhead structures, electrical wires, and door openings on the job site. Be sure this equipment and

operator will safely pass through and under.

Ø

Identify the load requirements for the job site. Do not exceed the load limits in weight or height as shown on safety

and operation requirements chart.

Under all operating conditions, the operator is solely responsible for a safe

and secure load. If job site conditions so warrant, reduce load and speed

.

Ø

Only operate this machine in daylight or OSHA conforming artificial light.

General Safety

SECTION 1

SAFETY

069583

Page 20

«
...
18
19
20
21
22
...
»

Содержание AW16-K 2019































































Отзывы:

Нет отзывов