allen AW16-K 2019 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 62

allen AW16-K 2019 Скачать руководство пользователя страница 50

Place buggy on level ground, shut off engine, apply parking brake, and block all wheels before servicing. Should
bucket or platform need to be kept in the raised position, securely block bucket in raised position. Service Buggy
only in well lit area, free from vehicle and pedestrian traffic.

WHEN BUCKET IS RAISED, THE SPACE BETWEEN RAISED BUCKET AND BUGGY FRAME IS A
PINCH POINT.

Machine Clean Up:

THIS BUGGY MUST BE CLEANED DAILY TO PREVENT CONCRETE AND DIRT BUILD-UP FROM
ADVERSELY AFFECTING SAFE MACHINE OPERATION. WASH BUGGY DOWN EACH DAY WITH
WATER.

Important areas to clean:

1. Tires (6)

2. Brake covers (2) & linkage

3. Operator’s platform

4. Hydraulic reservoir cover (keep all louvers clean).

5. Parking brake and linkage

6. Dump lever controls including foot control linkage and console mounted lever, or

handlebar mounted lever on machines so equipped.

7. Bucket

8. Handlebar and speed control lever

9. Directional control lever

10. Hydraulic lift cylinder

11. Crawler tracks on machines so equipped.

NOTE: Do not spray water on hot engine.

Engine Maintenance:

Follow engine maintenance schedules as outlined in the engine manual. Check engine oil daily.
Allow engine to warm up at idle before applying load. On Buggies equipped with electric start,
disconnect the battery, negative connection first. When reconnecting battery, connect positive
connection first.

Maintenance

SECTION 3

SERVICE

069583

Page 50

«
...
48
49
50
51
52
...
»

Содержание AW16-K 2019































































Отзывы:

Нет отзывов