allen AW16-K 2019 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 62

allen AW16-K 2019 Скачать руководство пользователя страница 19

9) Before adding fuel:

• Extinguish smoking materials.

• Shut engine off.

• Shut off Fuel. On AW16-K turn Fuel Valve at the carburetor to the OFF position.

Note: Fuel shut off on AW21-K occurs when the ignition key is turned OFF.

• Let engine cool for a minimum of 5 minutes.

• Inspect Buggy for Fuel leaks. Repair any fuel leak(s) BEFORE refueling.

• Do not stand on Buggy Operator Platform while refueling.

• Add Fuel using only non-metal, UL approved portable fuel containers. If using

a funnel it must be plastic without a screen or filter.

• Do not overfill.

• Replace fuel cap after adding fuel.

• A hot engine can ignite spilled gasoline.

EXERCISE EXTREME CAUTION WHEN REFUELING.

10) Make any necessary repair or adjustments before putting this equipment into operation. All guards must be
replaced; refer to the SERVICE section of this manual.

11) The above inspection procedures must also be performed by rental store personnel prior to each rental of this
equipment.

C) Familiarize yourself with the work site and job conditions.

This equipment must only be operated by trained personnel who fully understand its safe

operation. Each operator must be able to identify any unsafe work site conditions and
report these conditions to his supervisor for immediate correction.

Ø

The Gasoline Engine on this machine produces carbon monoxide (CO) and hydrocarbon (HC) emissions through

its exhaust. Inhalation of this exhaust gas can cause serious injury or death.

Ø

Engine exhaust and some of its constituents are also known to cause cancer, birth defects, and other reproduc-

tive harm.

Ø

The monitoring of carbon monoxide on the job site by a qualified inspector following OSHA guidelines is man-

datory in order to determine the safety of job site ventilation. In Canada follow Provincial Ministry of Labor OHSA
guidelines.

Ø

Do not use this machine without safe job site ventilation.

Ø

Do not operate this machine on an elevator. Using this machine on an elevator will cause unsafe job site

ventilation.

General Safety

SECTION 1

SAFETY

069583

Page 19

«
...
17
18
19
20
21
...
»

Содержание AW16-K 2019































































Отзывы:

Нет отзывов