allen AW16-K 2019 Скачать руководство пользователя страница 37

Страница: 37 / 62

Brake Operational Problem

Adjustment/Repair Required

Adjustment/Repair Procedure

1) Brake pedal (44) travels below

operator’s platform before brake

engages.

1) Clean concrete/dirt accumulation

away from brake pedal (44).

2) Adjust & lube pivot bolt (47) and

pedal (44).

3) Replace spring (48) if damaged or

worn.

Clean all dirt from pedal area. Adjust

clearance of brake pedal (44) with pivot

bolt assembly (47) by tightening 5/8” jam

nut against flat washers and ¾” hex nut.

Back off jam nut ¼ turn. While holding pivot

bolt (47) tighten 5/8” locknut to 120 ft. lbs.

Spray pivot bolt assy. (47) with lube.

5) Engine fails to stall during brake

test and/or buggy travels more

than 8’ during brake inspection

1) Tighten brake bands.

2) Clean concrete/dirt /oil accumula-

tion away from brake bands.

3) Hydrostatic pump is worn (Engine

fails to stall). 4) Replace worn brake

bands(s) (Brass rivets are contacting

brake drum and/or brake lining worn

less than 1/8” thick).

See “Adjustment/Repair Procedure” Rec-

ommended for “Brake Operational Prob-

lem”, items #1 and #3 above. See “Adjust-

ment/Repair Procedure” Recommended for

“Brake Operational Problem”, item #3 If

Hydrostatic Pump is suspect return it to the

Miller Spreader Company or to an autho-

rized Eaton Repair Facility. See “Adjust-

ment/Repair Procedure” Recommended for

“Brake Operational Problem”, item #3

After any brake service/adjustment apply approved lube to all brake pivot points.

Brake Service, continued

SECTION 3

SERVICE

069583

Page 37

Содержание AW16-K 2019































































Результаты поиска

Содержание AW16-K 2019

Отзывы:

allen AW16-K 2019, Инструкция по безопасности и эксплуатации, Страница: 37 / 62

Результаты поиска

Содержание AW16-K 2019

Отзывы: