Allen-Bradley PanelView 800 2711R-T10T Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 158

Allen-Bradley PanelView 800 2711R-T10T Скачать руководство пользователя страница 15

Rockwell Automation Publication 2711R-UM001E-EN-E - January 2017

15

Overview

Chapter

1

PanelView Explorer

PanelView Explorer is the browser interface for interacting with PanelView 800
terminals. Through this interface you can configure the terminal settings, transfer
files, test and run applications. See

Configuration Interfaces on page 17

for more

information on using PanelView Explorer.

Peripheral Connection

PanelView 800 terminals have a USB host port. You can power USB peripherals
directly from the PanelView 800 terminal. If the USB peripheral is not powered
directly from the PanelView USB port either:

• install the USB peripheral in the same enclosure as the PanelView terminal

and make sure it is connected to the same ground system.

• connect to the USB peripheral through a galvanically isolated hub.

IMPORTANT

The PanelView Explorer feature is only supported on PanelView 800
terminals with firmware revision 2.020 or earlier. It is not supported
from firmware revision 3.011 onwards.

WARNING:

If you connect or disconnect the communications cable

with power applied to this module or any device on the network, an
electrical arc can occur. This could cause an explosion in hazardous
location installations.
Be sure that power is removed or the area is nonhazardous before
proceeding.

WARNING:

If you connect or disconnect the USB cable with power

applied to this module or any device on the USB network, an electrical
arc can occur. This could cause an explosion in hazardous location
installations.
Be sure that power is removed or the area is nonhazardous before
proceeding.

ATTENTION:

Removing the USB flash drive or micro-SD card, from the

PanelView 800 terminal, while a firmware upgrade is in process, could
corrupt the firmware and make the terminal unusable. Take precautions
to prevent the USB flash drive or micro-SD card from being accidentally
disconnected. Also, do not power off the terminal while a firmware
upgrade is in progress.
USB hubs can produce unexpected behaviors and as a result are not
recommended.

«
...
13
14
15
16
17
...
»

Содержание PanelView 800 2711R-T10T































































































































































Отзывы:

Нет отзывов