Allen-Bradley PanelView 800 2711R-T10T Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 158

Allen-Bradley PanelView 800 2711R-T10T Скачать руководство пользователя страница 100

100

Rockwell Automation Publication 2711R-UM001E-EN-E - January 2017

Chapter 8

Troubleshoot the System

PanelView 800 Terminal Alerts

Category

ID

Description

Corrective Action

Communication

2

Data Access Error for Alias /*S:0 Param2*/,
Controller /*S:0 Param3*/, Address is /*S:0
Param4*/, Communication Flag is /*S:0 Param1*/

The terminal is having trouble reading the
external tag at this controller and address.

Check that the communication network cable is
connected.

If new ladder logic is downloading to the controller,
you could see this message. After the download,
communication should run normally.

Verify you have good communication to the
controller. If a remote device not responding alert
was present, then all external tags being actively
scanned will generate this alert.

Is the address configured in the controller? If so,
make sure all addresses of external tags to this
controller are configured at the controller. If one
address is outside of the range, a block of addresses
might show this condition. If the address is
configured as write only at the controller, this
address cannot be read. Set this external tag as
write only and remove panel devices from your
application that want to display data from this
external tag.

Communication

3

Communication Server Error

Contact technical support providing this data.
ID1-/*S:0 Param1*/, ID2-/*S:0 Param2*/, P1-/*S:0
Param3*/

Reboot the terminal.

Communication

4

Communication Server Error

Contact technical support providing this data.
ID1-/*S:0 Param1*/, ID2-/*S:0 Param2*/, P1-/*S:0
Param3*/, P2-/*S:0 Param4*/

Reboot the terminal.

Communication

5

Communication Server Error

Contact technical support providing this data.
ID1-/*S:0 Param1*/, ID2-/*S:0 Param2*/, P1-/*S:0
Param3*/, P2-/*S:0 Param4*/, P3-/*S:0 Param5*/

Reboot the terminal.

Communication

6

Communication Server Error

Contact technical support providing this data.
ID1-/*S:0 Param1*/, ID2-/*S:0 Param2*/, P1-/*S:0
Param3*/, P2-/*S:0 Param4*/, P3-/*S:0 Param5*/,
P4-/*S:0 Param6*/

Reboot the terminal.

Communication

7

Communication Server Error

Contact technical support providing this data.
ID1-/*S:0 Param1*/, ID2-/*S:0 Param2*/, P1-/*S:0
Param3*/, P2-/*S:0 Param4*/, P3-/*S:0 Param5*/,
P4-/*S:0 Param6*/, P5-/*S:0 Param7*/

Reboot the terminal.

«
...
98
99
100
101
102
...
»

Содержание PanelView 800 2711R-T10T































































































































































Отзывы:

Нет отзывов