Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 144

background image

1

Publication 1756-UM050A-EN-P - December 2001

Appendix

E

Autonegotiation Requirements

Manual Configuration on an
Ethernet Switch

The ControlLogix EtherNet/IP Bridge module supports the following
Ethernet settings:

•

10Mbps half duplex

•

10Mbps full duplex

•

100Mbps half duplex

•

100Mbps full duplex

Mode selection is done automatically based on the IEEE 802.3u
autonegotiation protocol.

If a module is connected to a port on a 10/100Mbps switch, you must
set this port to autonegotiate. If this port is set manually to one of the
modes listed above, a mismatch between module and switch modes
of operation may occur. This will result in significant reduction of
system performance.

Changing Ports on an
Ethernet Switch

If you reconnect the module from one port to another one, regardless
whether the new port is located on the same or a different switch (or
a hub), do the following:

1.

Disconnect the cable from the port to which the module is
currently connected.

2.

Wait until the module Link Status LED is off.

3.

Connect the cable to the new port.

This procedure will restart the autonegotiation process at the module
side. Another option is to restart the module itself.

«
...
127
128
129
130
131
...
»

Содержание ControlLogix 1756-ENBT

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ControlLogix 1756-ENBT

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 3

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: MAKOT Страницы: 6

Бренд: Oceanic Страницы: 11

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

TBEN-L 8IOL Series

Бренд: turck Страницы: 148

APEXpy 07-37A2-2111/ 520Series

Бренд: Bartec Страницы: 98

Бренд: Woodward Страницы: 32

Бренд: Euromatic Страницы: 20

Бренд: VMK Страницы: 98

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 217

iEP-5000G Series

Бренд: ASROCK Страницы: 2

Бренд: Runxin Страницы: 4

Бренд: Sunlover Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды