Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 114

Страница: 114 / 144

Publication 1756-UM050A-EN-P - December 2001

A-2

Troubleshooting

Link Status Indicator

The Link Status LED provides the following information:

OK Status Indicator

The OK Status LED provides the following module information:

Detailed network diagnostics are provided by the module’s Web
pages, which can be accessed through a network browser, such as
Netscape or Microsoft Internet Explorer. See Appendix B.

State

Status

Description

Off

No data
transmission

Module is not ready to communicate.

Green

Ready

Module is ready to communicate.

Flashing Green

Data transmission
in progress

Module is communicating over the network.

State

Status

Description

Off

No Power

Module does not have 24V DC power. Verify there
is chassis power and the module is completely
inserted into chassis and backplane.

Flashing Green

Standby

Module is not configured.

Green

Operational

Module is operating correctly.

Flashing Red

Minor Fault

A recoverable fault has been detected. This could
be caused by an error in the configuration.

Red

Major Fault

An unrecoverable fault has been detected.
Recycle power to the module. If this does not
clear the fault, replace the module.

Flashing Red and
Green

Self Test

Module performing power-up self-test.

Содержание ControlLogix 1756-ENBT
















































































































































Результаты поиска

Содержание ControlLogix 1756-ENBT

Отзывы:

Похожие инструкции для ControlLogix 1756-ENBT

Бренды по названию

Популярные бренды

Allen-Bradley ControlLogix 1756-ENBT, Руководство пользователя

Результаты поиска

Содержание ControlLogix 1756-ENBT

Отзывы:

Похожие инструкции для ControlLogix 1756-ENBT

Бренды по названию

Популярные бренды