Allen-Bradley 1734-IB8S Скачать руководство пользователя страница 126

Страница: 126 / 156

126

Rockwell Automation Publication 1734-UM013C-EN-P - August 2010

Chapter 8

Considerations When Replacing POINT Guard I/O Modules

If the project is configured for ‘Configure Always’, follow the appropriate steps to
replace a POINT Guard I/O module based on your scenario.

Remove the old I/O module and install the new module.

Right-click your POINT Guard I/O module and choose Properties.

Click the Safety tab.

Click Reset Ownership.

Click OK.

Follow your company-prescribed procedures to functionally test the
replaced I/O module and system and to authorize the system for use.

GuardLogix/

RSLogix 5000

Safety Signature

Exists

Replacement

Module SNN

Fault

Action Required

Yes or No

Out-of-box

None

None.

Yes or No

Same as original

None

None.

Yes or No

Different from original

SNN mismatch

Click Reset Ownership.
Follow the steps below.

Содержание 1734-IB8S





























































































































































Результаты поиска

Содержание 1734-IB8S

Отзывы:

Allen-Bradley 1734-IB8S, Инструкция по установке и эксплуатации, Страница: 126 / 156

Результаты поиска

Содержание 1734-IB8S

Отзывы: