background image

Operation 

 

 

 

 

3-16 

Algas-SDI Operation and Maintenance Manual 

– P/N - 52642 

2.  Close outlet shut-off valve at the exit of the vaporizer. 
3.  Start  burner  per  Direct  Fired  Vaporizer  startup  procedure  and  turn  the 

thermostat temperature control dial to the highest setpoint (7).  

4.  After  the  burner  cycles  off,  turn  thermostat  temperature  control  dial  to 

“OFF” position, shut off reigniter (if installed) and check that the pilot flame 
is extinguished. 

5.  After  the  pilot  flame  is  extinguished,  close  shut  off  valve  prior  to  the 

vaporizer in the liquid line. 

6.  Now  open  vaporizer  outlet  valve  and  flare  or  allow  attached  equipment  to 

consume the remaining gas in the line. 

7.  After  verifying  the  pressure  in  the  lines  is  zero  and  no  sources  of  ignition 

are present in the area, the vaporizer can now be disconnected.  

 

 

AUTOMATIC RE-IGNITION OPERATION 

 

Lighting or re-lighting of the pilot flame is accomplished by a spark across a gap 
of  approximately  1/8"  (3  mm)  from  the  electrode  tip  to  the  grounded  surface  of 
the pilot.  When the flame is established, the pilot flame conducts a current to the 
grounded  pilot  burner  and  a  solid-state  switch  in  the  unit  turns  off  the  spark.    If 
the pilot flame is extinguished, current to ground is interrupted and the solid-state 
switch  turns  on  the  spark,  which  sparks  at  a  nominal  timing  of  100  times  per 
minute,  re-lighting  the  pilot  flame  well  before  the  thermocouple  cools  enough  to 
drop out the thermostat safety system. 

Содержание Direct Fired 120/60H

























































Отзывы: