manualshive.com logo in svg

Algas SDI Direct Fired 120/60H, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Algas SDI Direct Fired 120/60H Скачать руководство пользователя страница 5

Symbols and Conventions 

Special symbols are used to denote hazardous or important information.  You 
should familiarize yourself with their meaning and take special notice of the 
indicated information. 

Please read the following explanations thoroughly. 

GENERAL WARNING OR CAUTION 

 

Indicates hazards or unsafe practices which can result in damage to 
the equipment or cause personal injury.  Use care and follow the 
instructions given. 
 

FLAMMABLE GAS HAZARD 

 

Indicates a potential hazard which can result in severe personal 
injury or death.  Use extreme care and follow the instructions given. 
 

ELECTRICAL DISCONNECT REQUIRED 

 

Indicates a potentially dangerous situation which can result in 
severe personal injury or death or damage to equipment.  Use great 
care and follow the instruction given. 
 

PARTS AND PRICES 

 

For parts and prices contact your Algas-SDI distributor. 
 

ASDI CONTACT NUMBERS 

 

If you have questions, need help with your equipment, or want 
information on other products, contact your distributor or 
Algas-SDI Global Support Center at: 
 
Telephone:  +1 206 762 4357 
 
Facsimile:   +1 206 789 5414 
 
Email: 

[email protected]

 

 
Internet: 

http://www.algas-sdi.com 

Содержание Direct Fired 120/60H

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды